Industrial Product Catalogue October 2016
PROCESS PIPING SYSTEMS
ACID WASTE PIPING SYSTEMS
THERMOPLASTIC VALVES
ULTRAGRIP MECHANICAL COUPLERS
STRAUB MECHANICAL COUPLERS
NATIONAL REACH. GLOBAL SUPPORT. Vinidex Pty Limited is Australia’s leading manufacturer and supplier of pipe systems and solutions for the transportation of fluid, data and energy. Vinidex is recognised internationally as a major participant in the pipe industry and as a quality manufacturer of PVC, Polyethylene (PE) and Polypropylene (PP) pipe systems.
As part of the world wide Aliaxis Group of companies Vinidex provides products, access to international technologies and innovative solutions that are world class. The Aliaxis Group is a leading global manufacturer and distributor of plastic pipe systems, present in over 40 countries, has more than 100 commercial entities and employs over 16 200 people.
From humble beginnings in 1960, Vinidex has grown to become Australia’s leading plastic pipes systems company. The company now has eleven manufacturing plants and thirteen distribution centres across Australia. Vinidex has products and systems solutions for a broad range of applications including plumbing, water supply, waste management, stormwater and drainage, mining, industrial, rural, irrigation, electrical, telecommunications and gas.
Our global reach extends across six continents and gives us unrivalled access to the most advanced pipe systems in the world. We are able to source a variety of new pipes and fittings technologies never before seen in the Australian market. These products support our ever-growing and expanding range and allow us to maintain our position as Australia’s leading manufacturer and supplier of quality pipe systems and solutions.
Proven long term performance and reliability of Vinidex products in major infrastructure and building projects has resulted in ongoing substitution of traditional materials such as metals, earthenware, concrete and fibre cement with better performing plastic pipes.
At every level of Vinidex you will find a genuine commitment from our staff to exceed expectations and ensure that you are satisfied with the overall experience. We offer a total solutions service from supply, technical and design assistance right through to installation, testing and evaluation.
Vinidex is renowned for a commitment to technical advancement and product innovation. Our continuous evaluation programs examine new materials, processing technology and manufacturing equipment to ensure our continued high standard in the pipes and fittings industry. Vinidex is recognised internationally as a major participant in the piping industry. We are represented and participate in Australian and ISO standards committees, Australian and International piping associations and the pipe industry generally. Our technologies and products are used in Europe, the USA and Africa. We have an ongoing presence in international developments in product and services to this industry.
Having built an enviable reputation in Australia and supported by an emphasis on product quality and customer service, Vinidex will continue to lead the industry in the development, manufacture and delivery of plastic pipeline and conduit systems.
INDUSTRIAL PRODUCT CATALOGUE PROCESS PIPING SYSTEMS
1
Xirtec 140 PVC
2
Corzan CPVC
9
Superflo ABS
15
DOUBLE CONTAINMENT SYSTEMS
37
ACID WASTE PIPING SYSTEMS
41
Vulcathene
42
THERMOPLASTIC VALVES
75
Ball Valves
76
Butterfly Valves
79
Check & Vent Valves
80
Diaphragm Valves
81
ULTRAGRIP MECHANICAL COUPLERS
83
STRAUB MECHANICAL COUPLERS
87
Process Piping Systems Vinidex offers a comprehensive range of integrated process piping systems – pipe, fittings and valves in ABS, PVC, CPVC, HDPE, PP and PVDF – designed to meet the temperature, pressure and size requirements of a wide range of chemical processing and similar industrial applications. In addition to costing less than common and exotic metal systems, our thermoplastic process piping systems are lightweight, as well as easy to handle, store, cut and join, so transportation and installation cost are substantially lower. When you specify a high-performance process piping system from Vinidex, you get the added benefits of a complete piping solution that is engineered for total integration, and backed by comprehensive support – all from one reliable source.
ii
Xirtec140 (PVC) and Corzan (CPVC) systems have been developed to meet industry demands for a complete Pipe, Valves and Fittings (PVF) package that is designed, produced and backed by a single manufacturer. These systems are engineered and manufactured to strict quality, performance and dimensional standards. Our high-performance vinyl systems are designed to meet the temperature, pressure and size requirements of piping systems used in chemical processes and other industrial applications. They feature outstanding resistance to photodegradation, creep stress and immunity to oxidation, and are exceptionally suited for use with a wide range of acids, alcohols, salts and halogens. The perfect extended service, low maintenance alternative to common and exotic metal systems. Xirtec140 and Corzan pipe and fittings are available in Schedule 80, IPS.
superFLO Chilled & cold water pipework
Durapipe SuperFLO ABS combines corrosion resistance, toughness and economic benefits to provide tremendous advantage for low temperature fluid transportation. SuperFLO ABS is a solvent welded, fully matched pipework system incorporating pipe, fittings and valves that is available in both imperial and metric sizes. SuperFLO ABS provides a wide temperature range and the system remains extremely ductile even at temperatures as low as -40°C. Furthermore, SuperFLO ABS is extremely lightweight and is much easier to handle on-site than traditional materials especially during installation which can significantly reduce both time and cost.
1
Xirtec 140 PVC Sch. 80
PVC Sch. 80 Pipe Dimension inches
VX Code
Dimension inches
92112
½
92286
¾x¾x½
92113
¼
92728
1x¾x1
¾
92287
1x1x½
92115
1
92288
1x1x¾
92116
1½
92729
1¼ x 1 x ¾
92117
1¼
92730
1¼ x 1¼ x ¾
92118
2
92731
1¼ x 1¼ x 1
92119
3
92289
1½ x 1½ x ¾
92120
4
92290
1½ x 1½ x 1
92121
6
92291
2x2x½
92292
2x2x¾ 2x2x1
92114
Tee
Soc x Soc x Soc 92727
¼
92293
92274
½
92294
2 x 2 x 1½
92275
¾
92295
3x3x2
1
92296
4x4x2
1¼
92297
4x4x3
1½
92298
6x6x3
92279
2
92299
6x6x4
92280
3
92281
4
92524
¼
92282
6
92161
½
92162
¾
92276 92277 92278
Tee
Soc x Soc x Fpt
90º Elbow
Soc x Soc
½
92163
1
92305
¾
92164
1¼
92306
1
92165
1½
92166
2
92167
3
92168
4
92169
6
92304
Tee
Unequal Tee Soc x Soc x Soc
VX Code
Fpt x Fpt x Fpt 92733
¼
92301
½
92302
¾
92303
1
92734
1¼
92735
1½
92736
2
92737
3
92738
4
90º Elbow
Fpt x Fpt
92525
¼
92526
½
92527
¾
92528
1
92529
1¼
92530
1½
92531
2
92532
3
92533
90º Elbow
2
4
Soc x Fpt
92518
½
92519
¾
92520
1
92521
1¼
92522
1½
92523
2
Xirtec 140 PVC Sch. 80
45º Elbow VX Code
Soc x Soc Dimension inches
Reducer Coupling VX Code
Soc x Soc Dimension inches
92408
¼
92258
¾x½
92149
½
92259
1x½
92150
¾
92260
1x¾
92151
1
92261
1¼ x ¾
92152
1¼
92262
1¼ x 1
92153
1½
92263
1½ x ½
92154
2
92264
1½ x ¾
92155
3
92265
1½ x 1
92156
4
92266
1½ x 1¼
92157
6
92755
2x½
92267
2x1
92268
2 x 1½
92269
3x2
92270
4x2
92271
4x3
92272
6x4
45º Elbow
Fpt x Fpt
92426
¼
92427
½
92437
¾
92438
1
92486
1¼
92495
1½
92496
2
92534
¼
92516
3
92173
½
92517
4
92174
¾
Coupling
Soc x Soc
Female Adapter
Soc x Fpt
92175
1 1¼
92171
¼
92176
92137
½
92177
1½
92138
¾
92178
2
92139
1
92179
3
92140
1¼
92180
4
92141
1½
92142
2
92143
3
92331
½
92144
4
92332
¾
92145
6
92333
1
92334
1¼
Coupling
Fpt x Fpt
Female Adapter
Soc x Fpt (SS reinforced)
92172
¼
92335
1½
92190
½
92336
2
92201
¾
92337
3
92202
1
92338
4
92203
1¼
92237
1½
92273
2
92323
½
92283
3
92284
4
92324
¾
Reducer Coupling
Fpt x Fpt
Female Adapter
Spig x Fpt (SS reinforced)
92325
1
92326
1¼
92720
½x¼
92327
1½
92721
¾x½
92328
2
92722
1x½
92329
3
92723
1x¾
92330
4
92724
1¼ x ¾
92725
1½ x 1
92726
2 x 1½
3
Xirtec 140 PVC Sch. 80
Male Adapter VX Code
Soc x Mpt Dimension inches
92204
½
92205
¾
92206
1
92207
1¼
92208
1½
92209
2
92210
3
92211
4
Cap Soc
Cap
Wye
92125
½
92126
¾
92127
1
92128
1¼
92129
1½
92130
2
92131
3
Fpt
Sp x Soc (flushstyle) VX Code Dimension inches 92688
½x¼
92215
¾x½
92216
1x½
92217
1x¾
92218
1¼ x ½
92219
1¼ x ¾
92220
1¼ x 1
92221
1½ x ½
92222
1½ x ¾
92223
1½ x 1
92224
1½ x 1¼
92225
2x½
92226
2x¾
92227
2x1
92228
2 x 1¼
92229
2 x 1½
92230
3x1
92135
¼
92231
3 x 1½
92136
½
92232
3x2
92146
¾
92233
4x2
92147
1
92234
4x3
92148
1¼
92235
6x2
92158
1½
92689
6x3
92159
2
92236
6x4
92160
3
92170
4
Soc x Soc x Soc
Reducer Bushing Sp x Fpt (flushstyle) 92238
½x¼
92749
1½
92240
¾x¼
92750
2
92241
¾x½
3
92242
1x½
4
92243
1x¾
92753
6
92244
1¼ x ½
92754
6x4
92245
1¼ x ¾
92751 92752
½” - 2” Wye – 1600 kpa maximum internal pressure rating @ 20ºC 3” - 6 x 6 x 4” Wye – 1000 kpa maximum internal pressure rating @ 20ºC
4
Reducer Bushing
92246
1¼ x 1
92247
1½ x ½
92248
1½ x ¾
92249
1½ x 1
92250
1½ x 1¼
92251
2x½
92252
2x¾
92253
2x1
92239
2 x 1¼
92254
2 x 1½
92713
3x¾
92714
3x1
92715
3 x 1¼
92716
3 x 1½
92255
3x2
92256
4x2
92257
4x3
92717
6x2
92718
6x3
92719
6x4
Xirtec 140 PVC Sch. 80
Reducer Bushing
Mpt x Fpt (flushstyle) VX Code Dimension inches 92690
½x¼
92691
¾x¼
92692
¾x½
92693
1x¼
92694
Union Soc x Soc (EPDM O-ring Seal) VX Code
Dimension inches
98320
¼
92307
½
92308
¾
92309
1 1¼
1x½
92310
92695
1x¾
92311
1½
92696
1¼ x ½
92312
2
1¼ x ¾
92313
3
92698
1¼ x 1
92314
4
92699
1½ x ½
92700
1½ x ¾
98321
¼
92701
1½ x 1
92702
1½ x 1¼
92759
½
92703
2x½
92760
¾
92704
2x¾
92705
2x1
92706
92697
Union Fpt x Fpt (EPDM O-ring Seal)
92761
1
92762
1¼
2 x 1¼
92763
1½
2 x 1½
92764
2
3 x 1½
92765
3
9279
3x2
98322
4
92711
4x2
92712
4x3
92707 92708
Plug
Spig 92687
Plug
2
Mpt 92680
¼
92212
½
92213
¾
Union Soc x Soc (Viton® O-ring Seal) 92739
¼
92315
½
92316
¾
92317
1
92318
1¼
92319
1½
92320
2
92321
3
92322
4
Union Fpt x Fpt (Viton® O-ring Seal)
92214
1
92740
¼
92681
1¼
92741
½
92682
1½
92742
¾
92683
2
92743
1
92684
3
92685
4
92744
1¼
92686
6
92745
1½
92746
2
92747
3
92748
4
Cross
Soc x Soc x Soc x Soc
92285
½
92300
¾
92375
1
92385
1¼
92386
1½
92396
2
92397
3
92407
4
5
Xirtec 140 PVC Sch. 80
Union Soc x Fpt (Viton® O-ring Seal) VX Code
Dimension inches
92572
½
Vanstone Flange Spig w PVC Ring VX Code
Dimension inches
¾
92555
½
92574
1
92556
¾
92575
1¼
92557
1
92576
1½
92558
1¼
92577
2
92559
1½
98323
3
92560
2
98324
4
92756
3
92757
4
92758
6
92573
One Piece Flange Soc 92535
½
92536
¾
Vanstone Flange Soc w PVC Ring
92537
1
92191
½
92538
1¼
92192
¾
92539
1½
92193
1
92540
2
92194
1¼
92541
3
92195
1½
92542
4
92196
2
92543
5
92544
6
92197
3
92198
4
92199
5
92200
6
One Piece Flange Fpt 92545
½
92546
¾
92547
1
92548
1¼
92549
1½
92550
2
92551
3
92552
4
92553
6
Blind Flange 92181
½
92182
¾
92183
1
92184
1¼
92185
1½
92186
2
92187
3
92188
4
92189
6
Vanstone Flange Fpt 92564
½
92565
¾
92566
1
92567
1¼
92568
1½
92569
2
92570
3
92571
4
Heavy Duty Vanstone Flange Spig w Fibre-Loc Ring 92561
3
92562
4
92563
6
All Moulded Flanges are rated at 1000 kpa at 20ºC., non-shock. CAUTION: When thermoplastic flanges are used with butterfly valves or other equipment, where a full face continuous support does not exist, a back-up ring or fiberglass reinforcement should be used to prevent cracking of the flange face. 6
Xirtec 140 PVC Sch. 80
Nipples VX Code
Nipples Dimension inches
VX Code
¼” diameter 92578 close
standard
92586
Dimension inches
¾” diameter ⁄8 close
7
1½
92593
2
92594
2½
92595
3
92596
3½
92597
4
92598
close
standard
92588
1½
92613
2
92614
2½
92615
3
92616
3½
92617
4
92618
4½
92619
5
4½
92620
5½
92599
5
92621
6
92600
6
92622
8
98325
10
92623
10
98326
12
92624
12
1” diameter
½” diameter 92579
11⁄8 close
92587
1½
92601
2
92602
2½
92603
3
92604
3½
92605
4
92606
4½
92607
5
92608
5½
92609
6
92610
8
92611
10
92612
12
92580
1½ close
92589
2
92625
2½
92626
3
92627
3½
92628
4
92629
4½
92630
5
92631
5½
92632
6
92633
8
92634
10
92635
12
1¼” diameter 92581
15⁄8 close
92590
2
92636
2½
92637
3
92638
3½
92639
4
92640
4½
92641
5
92642
6
92643
8
92644
10
92645
12
7
Xirtec 140 PVC Sch. 80
Nipples VX Code
Expansion Joint 6” Travel EPDM Dimension inches
1½” diameter close
standard
Dimension inches
92339
½
92300
¾
92385
1
92396
1½
92397
2
98316
3
98318
4
92582
1¾ close
92591
2
92646
2½
92647
3
92648
3½
92649
4
92650
4½
92651
5
98294
½
5½
98296
¾
6
98298
1
92654
8
92201
1½
92655
10
92203
2
12
92273
3
92283
4
92652 92653
92656
Expansion Joint 6” Travel FPM
Expansion Joint 12” Travel EPDM
2” diameter
92285
½
92375
¾
92583
2 close
92592
2½
92657
3
92658
3½
92659
4
92660
4½
92661
5
92662
5½
92663
6
98295
½
8
92172
¾
10
92190
1
12
92202
1½
92237
2
98305
3
92284
4
92664 92665 92666
3” diameter 92584
25⁄8 close
92667
3
92668
4
92669
5
92670
6
92671
8
92672
10
92673
12
4” diameter
8
VX Code
92585
27⁄8 close
92674
4
92675
5
92676
6
92677
8
92678
10
92679
12
92386
1
98313
1½
92407
2
98317
3
98319
4
Expansion Joint 12” Travel FPM
Corzan CPVC Sch. 80
CPVC Sch. 80 Pipe
Tee
Tee
Tee
90º Elbow
Soc x Soc Dimension inches
VX Code
Dimension inches
VX Code
92355
½
98024
¼
92356
¾
92398
½
92357
1
92399
¾
92358
1½
92400
1
92359
1¼
92401
1¼
92360
2
92402
1½
92361
3
92403
2
92362
4
92404
3
92363
6
92405
4
92406
6
Soc x Soc x Soc
90º Elbow
Fpt x Fpt
98169
¼
92487
½
98025
¼
92488
¾
98026
½
92489
1
98027
¾
92490
1¼
98028
1
92491
1½
98029
1¼
92492
2
98030
1½
92493
3
98031
2
92494
4
98032
3
98170
6
98033
4
90º Elbow
Soc x Soc x Fpt
Soc x Fpt
98250
½
98220
¼
98251
¾
98019
½
98191
1
98249
¾
92767
2
98020
1
98021
1¼
98022
1½
Soc x Soc x Fpt 98182
¼
98183
½
98184
¾
98185
1
98186
1¼
98187
1½
98188
2
98189
3
98190
4
Fabricated Tee Soc x Soc x Soc 98171
¾x¾x½
98172
1x1x½
98173
1x1x¾
98216
1¼ x 1 x 1
98217
1¼ x 1
98174
1¼ x 1 x 1¼
98218
1½ x 1¼ x 1
98175
1½ x 1½ x ¾
92497
1½ x 1½ x 1
98176
2x2x½
98177
2x2x¾
92498
2x2x1
98178
2 x 2 x 1½
98179
3x3x2
92499
4x4x2
98180
4x4x3
98219
6x6x3
98181
6x6x4
98023
45º Elbow
2
Soc x Soc
98009 92387 92388 92389 92390 92391 92392 92393 92394 92395
45º Elbow
¼ ½ ¾ 1 1¼ 1½ 2 3 4 6
Fpt x Fpt
98010 98011 98012 98013 98014 98015 98016 98017 98018
¼ ½ ¾ 1 1¼ 1½ 2 3 4
22½º Elbow Soc x Soc 98221
2
98222
3
98223
4
9
Corzan CPVC Sch. 80
11¼º Elbow Soc x Soc
Reducer Bushing
VX Code
Dimension inches
VX Code
Spig x Soc Dimension inches
98224
2
98124
½x¼
98225
3
92447
¾x½
98226
4
92448
1x½
Cross Soc x Soc x Soc x Soc 98227
¼
92788
¾
92789
1
92790
1¼
98005
1½
98006
2
98007
3
98008
4
Coupling Soc x Soc 92778
¼
92376
½
92377
¾
92378
1
92379
1¼
92380
1½
92381
2
92382
3
92383
4
92384
6
Coupling Fpt x Fpt 92779
¼
92780
½
92781
¾
92782
1
92783
1¼
92784
1½
92785
2
92786
3
92787
Reducer Coupling
10
4
Soc x Soc
92472
¾x½
92473
1x½
92474
1x¾
92475
1¼ x ½
92476
1¼ x ¾
92477
1¼ x 1
92478
1½ x ½
92479
1½ x ¾
92480
1½ x 1
92481
1½ x 1¼
92482
2x¾
92483
2x1
98228
2 x 1¼
98166
2 x 1½
98168
3x2
98167
4x2
92484
4x3
92485
6x4
92449
1x¾
92450
1¼ x ½
98125
1¼ x ¾
92451
1¼ x 1
92452
1½ x ½
92453
1½ x ¾
92454
1½ x 1
92455
1½ x 1¼
92456
2x½
92457
2x¾
92458
2x1
98126
2 x 1¼
98127
2 x 1½
98208
3x1
98229
3 x 1¼
98128
3 x 1½
98129
3x2
98131
4x2
98132
4x3
98133
6x2
98134
6x3
98135
6x4
Corzan CPVC Sch. 80
Reducer Bushing Spig x Fpt
Male Adapter Soc x Mpt
VX Code
Dimension inches
VX Code
Dimension inches
98157
½x¼
92439
½
98158
¾x¼
92440
¾
92459
¾x½
92441
1
92460
1x½
92442
1¼
92461
1x¾
92443
1½
92462
1¼ x ½
92444
2
92463
1¼ x ¾
92445
3
92464
1¼ x 1
92446
4
92465
1½ x ½
92466
1½ x ¾
92467
1½ x 1
92468
1½ x 1¼
92469
2x½
92470
2x¾
92471
2x1
98159
2 x 1¼
98160
2 x 1½
98230
3x¾
98206
3x1
98231
3 x 1¼
98161
3 x 1½
98162
3x2
98163
4x2
98164
4x3
98233
6x3
98165
6x4
Female Adapter Soc x Fpt 98034
¼
92409
½
92410
¾
92411
1
92412
1¼
92413
1½
92414
2
92415
3
92416
4
Female Adapter
Soc x Fpt (SS reinforced)
Reducer Bushing Mpt x Fpt
98258
½
98259
¾
98260
1
98261
1¼
98262
1½
98263
2
98264
3 4
98136
½x¼
98265
98137
¾x¼
98138
¾x½
Female Adapter
98234
1x¼
98252
½
98139
1x½
98253
¾
98140
1x¾
98254
1
98141
1¼ x ½
98255
1¼
98142
1¼ x ¾
98256
1½
98143
1¼ x 1
98257
2
98144
1½ x ½
98235
3
98145
1½ x ¾
98236
4
98146
1½ x 1
98147
1½ x 1¼
98148
2x½
98149
2x¾
98150
2x1
98151
2 x 1¼
98152
2 x 1½
98153
3 x 1½
98154
3x2
98155
4x2
98156
4x3
Spig x Fpt (SS reinforced)
Cap
Soc 92768
¼
92366
½
92367
¾
92368
1
92369
1¼
92370
1½
92371
2
92372
3
92373
4
92374
6
11
Corzan CPVC Sch. 80
Cap Fpt
Union Fpt x Fpt (Viton® O-ring Seal)
VX Code
Dimension inches
VX Code
Dimension inches
92769
¼
92770
½
92771
¾
98193 98194 98195 98196 98197 98198 98199 98200 98238
¼ ½ ¾ 1 1¼ 1½ 2 3 4
92772
1
92773
1¼
92774
1½
92775
2
92776
3
92777
4
Plug Mpt 98115
¼
98116
½
98117
¾
98118
1
98119
1¼
98120
1½
98121
2
98122
3
98123
4
Union Soc x Soc (EPDM O-ring Seal) 92508 92509 92510 92511 92512 92513 92514 92515
½ ¾ 1 1¼ 1½ 2 3 4
Union Fpt x Fpt (EPDM O-ring Seal) 98215 98209 98210 98211 98212 98213 98214 98237
½ ¾ 1 1¼ 1½ 2 3 4
Union Soc x Soc (Viton O-ring Seal) ®
98192 92500 92501 92502 92503 92504 92505 92506 92507
¼ ½ ¾ 1 1¼ 1½ 2 3 4
45º Wye Soc x Soc x Soc 98239
½
98240
¾
98241
1
98242
1¼
98207
1½
98201
2
98202
3
98203
4
98204
6
98205
6x6x4
½” - 2” Wye – 1600 kpa maximum internal pressure rating @ 20ºC 3” - 6 x 6 x 4” Wye – 1000 kpa maximum internal pressure rating @ 20ºC
One Piece Flange Soc 98035
½
98036
¾
98037
1
98038
1¼
98039
1½
98040
2
98041
3
98042
4
98043
6
One Piece Flange Fpt 98044 98045 98046 98047 98048 98049 98050 98051
½ ¾ 1 1¼ 1½ 2 3 4
All Moulded Flanges are rated at 1000 kpa at 20ºC., non-shock. CAUTION: When thermoplastic flanges are used with butterfly valves or other equipment, where a full face continuous support does not exist, a back-up ring or fiberglass reinforcement should be used to prevent cracking of the flange face.
12
Corzan CPVC Sch. 80
Heavy Duty Vanstone Flange
Nipples
Soc
VX Code VX Code
Dimension inches
92428
½
92429
¾
92430
1
92431
1¼
92432
1½
92433
2
92434
3
92435
4
92436
6
Dimension inches
¼” diameter 98063 close
standard
⁄8 close
7
98071
1½
98079
2
98080
3
98081
4
98082
5
98083
6
½” diameter
Vanstone Flange Fpt 98243
½
98064
11⁄8 close
98244
¾
98072
1½
1
98085
2
98061
1¼
98084
3
98246
1½
98086
4
98247
2
98087
5
98062
3
98088
6
98248
4
98245
Vanstone Flange Spig
¾” diameter
98052
½
98073
1½
98053
¾
98089
2
98054
1
98090
3
98055
1¼
98091
4
98056
1½
98092
5
98057
2
98093
6
98058
3
98059
4
98060
6
Blind Flange 92417 92418 92419 92420 92421 92422 92423 92424 92425
½ ¾ 1 1¼ 1½ 2 3 4 6
1” diameter 98065
1½ close
98074
2
98094
3
98095
4
98096
5
98097
6
All Moulded Flanges are rated at 1000 kpa at 20ºC., non-shock. CAUTION: When thermoplastic flanges are used with butterfly valves or other equipment, where a full face continuous support does not exist, a back-up ring or fiberglass reinforcement should be used to prevent cracking of the flange face.
13
Corzan CPVC Sch. 80
Nipples VX Code
Expansion Joint 6” Travel EPDM Dimension inches
1¼” diameter close
standard
98066
15⁄8 close
98075
2
98098
3
98099
4
98100
5
98101
6
1½” diameter 98067
1¾ close
98076
2
98102
3
98103
4
98104
5
98105
6
2” diameter
Dimension inches
98280
½
98282
¾
98284
1
98286
1½
98288
2
98290
3
98292
4
Expansion Joint 12” Travel EPDM 98281
½
98283
¾
98285
1
98287
1½
98289
2
98291
3
98293
4
Expansion Joint 6” Travel FPM 98266
½
98268
¾
98068
2 close
98270
1
98077
2½
98272
1½
98106
3
98274
2
98107
4
98276
3
98108
5
98278
4
98109
6
3” diameter
Expansion Joint 12” Travel FPM 98267
½
98269
¾
2 ⁄8 close
98271
1
98110
3
98273
1½
98111
4
98275
2
98112
5
98277
3
98113
6
98279
4
98069
5
4” diameter
14
VX Code
98070
27⁄8 close
98078
4
92766
5
98114
6
15
SuperFLO ABS
SuperFLO ABS Pipe imperial system Plain Pipe - ABS Class C 130psig (9 bar)
d1 (mean)
Mean OD Thickness Length Weight Size d1 t (mm) (m) kg/m 6 168.3 9.9 6 5.12
90769
8
90770
219.1
12.7
6
8.57
Code
t (mean)
Pipe - ABS Class E 217psig (15 bar) Mean OD Thickness Length Weight Size d1 t (mm) (m) kg/m 3/8 17.1 1.7 6 0.09
90760
½
21.4 2.0
6
0.13
90761
¾
26.7 2.5
6
0.20
90762
1
33.6 3.1
6
0.31
90763
1¼
42.2 3.9
6
0.49
90764
1½
48.3 4.5
6
0.64
90765
2
60.3 5.6
6
1.00
90766
3
88.9 8.3
6
2.16
90767
6
3.59
90768
4
114.3
10.6
Code
Pipe - ABS Class T (for threading) 173 psig (12 bar after threading) Mean OD Thickness Length Weight Size d1 t (mm) (m) kg/m
16
Code
3/8 17.1
3.5
6
0.16
90807
½ 21.4
3.6
6
0.22
90808
¾
26.7 3.6 6 0.28 90809
1 33.6
4.3
6
0.43
90810
1¼ 42.2
5.3
6
0.65
90811
1½ 48.3
6.0
6
0.85
90812
2 60.3
7.2
6
1.28
90813
SuperFLO ABS
Sockets Plain
A
Z1 B
Size
PN
Z1 gms
Code
3/8 ½ ¾ 1 1¼ 1½ 2 3 4 6 8
15 21 32 2 4 15 26 38 2 6 15 32 43 3 12 15 41 50 3 24 15 52 60 4 41 15 60 66 2 62 15 74 78 4 114 15 108 104 4 355 15 136 135 5 595 12 201 191 9 2269 9 257 249 11 3668
A
B
90466 90467 90468 90469 90470 90471 90472 90473 90474 90475 90476
Reducing bushes Plain Size
PN
B
Z1
gms
Code
½ x 3/8
15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 12 9
17 20 23 24 28 28 28 30 30 30 31 38 38 38 37 51 51 65 93 110
2 3 6 4 12 8 5 13 10 7 4 15 15 11 7 21 15 12 27 23
7 8 23 15 21 24 20 26 37 40 19 45 45 57 42 130 178 277 666 1185
90510 90511 90512 90513 90505 90506 90514 90507 90508 90515 90516 90509 90517 90518 90519 90521 90522 90524 90525 90526
¾x ½
Z1
B
Z1
*
B
1x½ 1x¾ *1¼ x ½ *1¼ x ¾ 1¼ x 1 *1½ x ½ *1½ x ¾ *1½ x 1 1½ x 1¼ *2 x ¾ *2 x 1 *2 x 1¼ 2 x 1½ *3 x 1½ *3 x 2 *4 x 3 *6 x 4 *8 x 6
*Relief configuration (see drawing insert).
17
SuperFLO ABS
Reducing sockets Plain
C
A
Z1 B
Z1 gms
Code
¾ x ½ 15 32 44 26 7 11 1 x ¾ 15 41 53 33 9 19 1¼ x 1 15 52 63 41 10 39 1½ x 1¼ 15 59 68 51 8 58 2 x 1½ 15 74 82 59 12 100 3 x 2 15 108 114 75 26 320 4 x 3 15 136 136 108 20 558 6 x 4 12 205 213 140 55 1975 8 x 6 9 256 263 198 50 3410
Size
PN
A
B
C
90533 90534 90535 90536 90537 90538 90539 90540 90541
Elbows 45° Plain
Z1 C A
Size
PN
3/8
A
C
Z1 gms Code
½ ¾ 1 1¼ 1½ 2 3 4 6 8
15 21 20 6 8 15 27 26 8 9 15 33 27 12 15 15 41 37 13 25 15 52 44 15 59 15 60 50 18 86 15 82 66 27 160 15 112 94 40 750 15 139 115 50 1300 12 198 134 41 2390 9 259 182 65 5620
Size
PN
90571 90572 90573 90574 90575 90576 90577 90578 90579 90580 90581
Elbows 90° Plain
Z1 C
A
3/8
½ ¾ 1 1¼ 1½ 2 3 4 6 8
A
C
Z1 gms Code
15 21 24 9 6 15 26 29 12 11 15 32 34 14 19 15 41 41 17 35 15 52 49 21 70 15 60 56 26 101 15 74 68 31 191 15 111 104 52 720 15 141 130 65 1505 12 203 175 85 4075 9 256 251 112 6900
90542 90543 90544 90545 90546 90547 90548 90549 90550 90551 90552
Tees 45° Plain C Z2
A Z3 Z1 B 18
Size PN A B C Z1 Z2 Z3 gms
Code
½ ¾ 1 1¼ 1½ 2
90597 90598 90599 90600 90601 90602
9 9 9 9 9 9
28 68 44 34 33 81 52 41 41 97 63 49 50 117 80 61 60 140 97 80 74 170 113 90
27 7 30 32 8 45 39 9 80 52 10 194 67 12 298 73 15 546
SuperFLO ABS
Tees 90° Equal plain
Size PN A B C Z gms
Code
3/8 ½ ¾ 1 1¼ 1½ 2 3 4 6 8
90582 90583 90584 90585 90586 90587 90588 90589 90590 90591 90592
1
A
Z1
B
Z1 C
15 21 49 25 10 7 15 26 58 29 11 13 15 32 69 34 15 23 15 41 83 42 19 43 15 52 101 50 23 92 15 59 113 53 25 133 15 74 137 70 31 249 15 113 204 105 44 926 15 143 244 121 54 1960 12 205 355 175 88 4449 9 257 468 240 100 9600
Tees 90° Swept plain Size PN A
A
1 1½ 2 4
Z3 Z2
D
B C D Z1 Z2 Z3 gms
Code
9 41 115 79 79 57 57 14 85
90650
9 62 160 105 105 74 74 24 285 9 78 195 125 125 87 87 32 515 9 139 315 190 190 127 127 62 2080
90651 90652 90654
B
Z1 C
Bends 22 ⁄2° Long radius 1
C
R
Size PN C E R gms
Code
1 1½ 2 3 4 6 8
90719 90720 90721 90722 90723 90724 90725
15 15 15 15 15 12 9
76 38 102 46 110 57 152 143 113 73 203 274 202 114 305 857 262 152 407 1886 385 229 610 5154 503 305 812 8962
Tolerance on angle ±3°
E
19
SuperFLO ABS
Bends 45° Long radius
C
Size PN C E R gms Code
1 1½ 2 3 4 6 8
R
15 15 15 15 15 12 9
75 37 102 51 113 55 152 156 152 73 203 322 238 121 305 1100 300 145 407 2290 440 218 610 6290 592 280 812 11440
90712 90713 90714 90715 90716 90717 90718
Tolerance on angle ±3°
E
Bends 90° Long radius
R
C
Size
3 4 6 8
PN
C
E
R
15 403 98 15 545 138 12 817 207 9 1174 362
gms
305 407 610 812
1535 3440 9430 19070
Code 90708 90709 90710 90711
Tolerance on angle ±3°
E
Bends 90° Short radius plain
Size PN A C Z1 gms Code
½ ¾ 1 1¼ 1½ 2 3 4
Z1
C
A
15 26 56 43 20 15 33 65 45 45 15 40 85 63 65 15 51 108 81 130 15 62 134 102 290 15 73 165 126 560 15 111 226 172 1445 15 140 280 216 2400
90563 90564 90565 90566 90567 90568 90569 90570
Saddles Plain
B
pipe centre line
20
2 x 1¼
Z1 E
Size
3 x 1½ 4 x 2 A 6 x 2
PN
A
B
15 15 15 15
60 136 76 140 95 140 71 154
E
Z1 gms Code
48 33 90 60 46 158 74 58 230 73 86 225
Two saddles can be mounted diametrically opposite.
90593 90594 90595 90596
SuperFLO ABS
End caps Plain
FIG.1
A
B
FIG.2
Size
PN
3/8 ½ ¾ 1 1¼ 1½ 2 3 4
15 15 15 15 15 15 15 15 15
A
B gms
21 17 3 26 22 5 32 25 9 40 30 20 52 51 33 59 39 48 74 70 90 109 97 268 136 120 465
Fig
Code
1 1 1 1 2 1 2 2 2
90633 90634 90635 90636 90637 90638 90639 90640 90641
A
B
Socket unions Plain
A
Z2
Z1 B
Size PN A B Z1 Z2 gms
Code
3/8 ½ ¾ 1 1¼ 1½ 2 3 4
90685 90686 90687 90688 90689 90690 90691 90692 90693
15 39 44 5 10 25 15 43 49 5 10 36 15 51 55 5 10 51 15 64 65 7 12 86 15 72 77 10 14 122 15 79 92 13 16 160 15 102 112 15 19 297 9 155 113 6 4 750 9 180 138 7 6 1155
EPDM seal as standard. For FPM seal order 01 204 1**
21
SuperFLO ABS
Sockets Plain female BSP thread
A
Size PN A B C Z1 gms
Code
½ ¾ 1 1¼ 1½ 2 3
90477 90478 90479 90480 90481 90482 90483
12 27 38 17 4 12 33 44 20 2 12 42 51 23 5 12 52 55 22 4 12 60 61 26 2 12 75 70 29 2 12 110 107 52 3
8 14 30 46 65 114 378
Z1 C B
Reducing bushes Plain female BSP thread
Z1
Size
PN B Z1 gms
½ x 3/8 3/8 x ½ 1 x ¾
12 17 6 4 90527 12 20 5 7 90528 12 23 6 12 90529
Code
B
Elbows 90° Plain female BSP thread Size PN A C Z1 gms Code
Z1 C
½ ¾ 1 1½ 2
12 26 34 17 26 12 32 36 20 34 12 40 41 23 63 12 62 57 30 136 12 75 66 35 203
90553 90554 90555 90556 90557
Z1 A
Female threaded adaptors Plain spigot end/female BSP thread
A
Z1 B
22
Size PN A B Z1 gms
Code
½ ¾ 1 1¼ 1½ 2
90662 90663 90664 90665 90666 90667
12 12 12 12 12 12
27 38 16 8 36 44 18 14 43 50 21 24 55 60 22 49 63 66 25 68 78 78 29 129
SuperFLO ABS
Hexagon nipples Plain spigot/male BSP thread
A(A/F)
Size PN A B D gms
3/8 ½ ¾ 1 1¼ 1½ 2
12 24 36 12 30 42 12 36 48 12 46 56 12 46 60 12 55 63 12 72 74
11 7 15 12 16 30 20 40 21 50 22 58 26 91
Code 90498 90499 90500 90501 90502 90503 90504
D B
Male threaded adaptors Plain/male BSP taper threaded
A
Size PN A B D Z1 gms
Code
3/8
12 22 35 10 20 5 90655 ½ 12 27 45 12 28 9 90656 ¾ 12 35 48 14 28 14 90657
D Z1 B
A(A/F)
Size PN A B D Z1 gms
Code
1 12 46 58 19 35 36 1¼ 12 56 66 22 38 70 1½ 12 72 75 22 43 115 2 12 80 85 26 46 150
90658 90659 90660 90661
D Z1 B
Barrel nipples Plain/BSP taper threaded Size
PN
3 4
12 12
B 128 153
D
gms
Code
30 36
252 525
90731 90732
D B
23
SuperFLO ABS
Hose adaptors BSP taper threaded/hose tail Size PN A B C D E gms Code ½ 12 26 60 41 13 14 8 ¾ 12 28 66 41 16 20 15 1 12 40 73 46 19 27 28
90675 90676 90677
A(A/F)
E
C
D B
Tank connectors Plain spigot/male BSP parallel thread Size
A
B
C
D
F
gms
Code
½ 28 70 38 28 15 26
90706
¾ 33 77 38 38 21 30
90707
F A(A/F) C
D B
Composite unions Plain/brass, female BSP parallel thread
A(A/F)
Z1
Size PN
A
B
Z1 Z2 gms
Code
½ ¾ 1 1¼ 1½ 2
40 48 55 65 79 88
42 3 7 165 49 3 9 290 59 11 12 310 68 9 10 450 75 12 14 800 90 14 14 950
90694 90695 90696 90697 90698 90699
15 15 15 15 15 15
Fitted with brass retaining nut.
Z2
Brass material to BS2872, WRAS approved.
B ALL Durapipe Brass Components are manufactured using DZR Brass.
Composite unions Plain/brass, male BSP taper thread
A(A/F)
Z1 B
Size
PN
A
Z1 gms
Code
½ ¾ 1 1¼ 1½ 2
15 15 15 15 15 15
40 54 3 175 48 74 3 320 55 86 8 420 65 94 10 620 78 108 13 1000 88 129 15 1200
B
90700 90701 90702 90703 90704 90705
Fitted with brass retaining nut. Brass material to BS2872, WRAS approved. ALL Durapipe Brass Components are manufactured using DZR Brass.
24
SuperFLO ABS
Sockets Female BSP taper thread Size PN A B gms Code ½ ¾ 1 1¼ 1½ 2 3
A
12 12 12 12 12 12 12
26 38 12 33 43 22 41 51 34 51 54 60 62 63 87 75 72 132 110 107 437
90484 90485 90486 90487 90488 90489 90490
B
Reducing bushes Male/female BSP thread
A(A/F)
Size PN A B D gms
Code
½ x 3/8 12 24 25 10 5 ¾ x ½ 12 30 27 11 10 1 x ¾ 12 36 31 12 13
90530 90531 90532
Male thread taper. Female thread parallel.
D B
Elbows 90° Female BSP taper thread Size PN A C Z1 gms Code
Z1 C
½ 12 26 29 17 27 ¾ 12 32 33 19 39 1 12 41 41 23 65 1½ 12 63 57 30 141 2 12 75 67 35 212
90558 90559 90560 90561 90562
A
End caps Female BSP taper thread
A
D B
Size PN A B D gms Code
3/8 ½ ¾ 1 1¼ 1½ 2 3
12 12 12 12 12 12 12 12
26 27 36 44 55 63 78 111
20 20 23 28 31 35 40 65
16 5 16 6 17 10 21 18 22 33 25 50 28 90 53 262
90642 90643 90644 90645 90646 90647 90648 90649
25
SuperFLO ABS
Plugs Male BSP taper thread
A(A/F)
D
Size PN A B D gms
3/8 ½ ¾ 1 1¼ 1½ 2
12 11 19 12 13 23 12 14 28 12 17 30 12 22 35 12 27 38 12 37 45
10 3 14 5 15 8 17 12 22 30 22 36 26 50
Code 90668 90669 90670 90671 90672 90673 90674
B
Hexagon nipples Male BSP taper thread Size PN A B D gms Code A(A/F)
D
3/8
½ ¾ 1 1¼ 1½
2
12 12 12 12 12
24 30 36 46 46
38 46 50 59 67
12 12
55 73 72 81
14 6 18 12 19 30 13 40 27 55
90491 90492 90493 90494 90495
29 75 33 125
90496 90497
B
Back nuts Female BSP taper thread Size PN A B C gms Code 3/8 12 25 11 29 5 ½ 12 28 13 38 8 ¾ 12 33 13 38 15 1 12 45 16 54 18 1¼ 12 50 18 58 19 1½ 12 60 19 69 31 2 12 79 21 91 65
C A(A/F)
90678 90679 90680 90681 90682 90683 90684
B
Flanges stub Plain/serrated
A
Size PN A B
D Z1 gms
Code
2 3 4 6 8
14 3 90 18 6 200 20 6 350 24 11 805 26 14 2075
90628 90629 90630 90631 90632
15 15 15 12 9
96 40 127 57 159 69 213 104 269 132
Z1 D B
26
All Durapipe flanges are designed for use with Durapipe backing rings. Guarantees are null and void if used with incorrect backing ring.
SuperFLO ABS
Flanges full face Plain/drilled BS10 Table D/E No. of Hole Size A B D Z1 P.C.D. Holes Diameter gms
A
Z1 B
D
Code
½ 96 21 10 4 67 4 14 68 90612 ¾ 105 24 10 4 73 4 14 78 90613 1 115 27 10 4 83 4 14 107 90614 1¼ 140 33 10 5 87 4 14 122 90615 1½ 150 37 10 5 98 4 14 154 90616 2 166 45 10 6 115 4 18 223 90617 3 199 60 11 8 145 4 18 398 90618 *4 220 72 14 6 178 8 18 638 90619 6 284 98 22 8 235 8 22 1340 90620 *4” BS10 Table D has 4 holes and should be ordered as 01 317 110.
BS4504 Table 16/3-10/3 No. of Size
A
B
D
Hole Z1 P.C.D. Holes Diameter gms
Code
½ 96 21 10 4 65 4 14 68 90733 ¾ 105 24 10 4 75 4 14 78 90734 1 115 27 10 4 85 4 14 107 90735 11⁄4 140 33 10 5 100 4 18 122 90736 11⁄2 150 37 10 5 110 4 18 154 90737 2 166 45 10 6 125 4 18 223 90738 3 199 60 11 8 160 8 18 398 90739 4 220 72 14 6 180 8 18 638 90740 6 284 98 22 8 240 8 22 1340 90741
ANSI Class 150 No. of
Size
A
B
D
Hole Z1 P.C.D. Holes Diameter gms
Code
½ 96 21 10 4 60 4 14 68 90742 ¾ 105 24 10 4 70 4 14 78 90743 1 115 27 10 4 80 4 14 107 90744 1½ 150 37 10 5 98 4 14 154 90745 2 166 45 10 6 121 4 18 223 90746 3 199 60 11 8 152 4 18 398 90747 4 220 72 14 6 190 8 18 638 90748 6 284 98 22 8 241 8 22 1340 90749
Undrilled Size PN A B D Z1 gms
Code
½ ¾ 1 1¼ 1½ 2 3 4 6
90603 90604 90605 90606 90607 90608 90609 90610 90611
15 15 15 15 15 15 15 15 12
96 105 115 140 150 165 199 220 284
21 24 27 32 36 45 60 73 99
10 10 10 10 10 11 11 14 22
4 75 4 85 4 111 4 130 5 160 6 233 8 414 6 657 8 1417
Note: Durapipe backing rings must be used in conjunction with full face flanges.
All Durapipe flanges are designed for use with Durapipe backing rings. Guarantees are null and void if used with incorrect backing ring.
27
SuperFLO ABS
Flanges blanking Plain/drilled BS10 Table D/E
No. of Hole Size A B P.C.D. Holes Diameter gms 2 165 13 115 4 18 235 3 197 19 145 4 18 520 *4 214 19 178 8 18 720 6 286 26 235 8 22 1575 8 337 26 292 8 22 2300
A
Code 90726 90727 90728 90729 90730
*4” BS10 Table D has 4 holes and should be ordered as 01 326 110.
BS4504 Table 16/3 (½” to 8”) 10/3 (½” to 6”) No. of Hole Size A B P.C.D. Holes Diameter gms 2 165 13 125 4 18 235 3 197 19 160 8 18 520 4 214 19 180 8 18 720 6 286 26 240 8 22 1575 8 337 26 295 12 22 2300
B
Code 90750 90751 90752 90753 90754
ANSI Class 150 No. of Hole Size A B P.C.D. Holes Diameter gms 2 165 13 121 4 18 235 3 197 19 152 4 18 520 4 214 19 190 8 18 720 6 286 26 241 8 22 1575 8 337 26 298 8 22 2300
Code 90755 90756 90757 90758 90759
Undrilled Size
PN
1 1½ 2 3 4 6 8
15 15 15 15 15 12 9
A 116 150 166 197 214 286 337
B
gms
13 140 13 185 13 235 19 520 19 720 26 1575 26 2300
Code 90621 90622 90623 90624 90625 90626 90627
Note: Durapipe backing rings must be used in conjunction with blank flanges.
Backing rings Galvanised mild steel drilled BS10 Table D/E
No. of Hole Size A B C P Holes Dia. ½ 95 6 35 67 4 ¾ 103 7 45 73 4 1 114 6 49 83 4 1¼ 120 7 60 87 4 1½ 135 7 68 98 4 2 151 8 78 115 4 3 187 9 110 145 4 *4 216 9 140 178 8 6 282 11 195 235 8 8 337 10 255 292 8
P
C
L B
28
A
14 14 14 14 14 18 18 18 22 22
Bolt Size
Weight gms
M12x50 270 M12x50 300 M12x50 380 M12x50 380 M12x50 480 M16x65 880 M16x70 1040 M16x80 1330 M20x90 2340 M20x100 2870
Code 90836 90837 90838 90839 90840 90841 90842 90843 90845 90846
*4” BS10 Table D has 4 holes and should be ordered as 03 415 110.
All Durapipe flanges are designed for use with Durapipe backing rings. Guarantees are null and void if used with incorrect backing ring.
SuperFLO ABS
VKD Double union ball valves Manual – EPDM seals d
DN
PN
½ ¾ 1 1¼ 1½ 2
15 20 25 32 40 50
16 16 16 16 16 16
L 16.5 19 22.5 26 30 36
Z
H
70 77 83 94 104 127
E
B
C
103 55 49 66 115 66 59 75 128 75 66 85 146 87 75 97 164 100 87 110 199 122 101 134
gms
Code
160 265 345 550 730 1280
90771 90772 90773 90774 90775 90776
Options: FPM seals (plain ends) order H0 DKB*** FPM seals (threaded ends) order H0 DKB*** Manual valves can be supplied with locking kits - further information is available from our Valve Department. d
DN PN
Z
L
H
H1 E B B1 C C1 gms Code
3
80 16 168 51 270 149 203 177 105 327 272 5700
90777
4
100 16 186 61 308 167 238 195 129 385 330 8660
90778
Options: FPM seals (plain ends) order H0 DKB***
VKD & TKD ball valves can be supplied electrically or pneumatically actuated.
SX Easyfit ball check valves Plain ends – EPDM seals (other options available) d DN PN L Z H E gms Code
½ ¾ 1 1¼
15 20 25
16 16 16
16.5 19 22.5
50 53 59
82 91 103
54 63 72
133 171 270
90781 90782 90783
32 16 26 68 120 85 414 90784 1½ 40 16 30 77 139 100 608 90785 2 50 16 36 98 174 118 972 90786
Options: EPDM seals (threaded ends) order H0 SXA B** FPM seals (plain ends) order H0 SXB*** FPM seals (threaded ends) order H0 SXB B**
Note: this valve must be installed at a minimum distance of 10 x nominal diameter (eg. 20" for size 2") from pump flange.
29
SuperFLO ABS
RV Y-Type strainers Plain ends – EPDM seals d
DN
PN
A
Grey
max
15 20 25
15 15 15
125 145 165
32 40 50
15 15 9
190 111 87 26 155 207 A 733 210 120 100 31 181 243 A 1095 240 139 120 38 222 298 A 1843
½ ¾ 1 1¼ 1½ 2
B
E
L
72 84 95
55 66 75
16 19 22
Z
H Fig. gms
103 135 A 120 158 A 132 176 A
Code
211 358 526
90787 90788 90789 90790 90791 90792
Options: EPDM seals (threaded ends) order H0 RVA B** FPM seals (plain ends) order H0 RVB*** FPM seals (threaded ends) order H0 RVB B**
DK Diaphragm valves Manual – plain union ends – EPDM seals d
DN PN
B
½ ¾ 1 1¼
15 20 25
95 26 124 95 26 144 95 26 154
9 9 9
B1 H h H1 J L gms 12 12 12
90 90 90
M6 M6 M6
16 19 23
32 9 126 40 174 18 115 M8 27 1½ 40 9 126 40 194 18 115 M8 32 2 50 9 148 40 224 18 140 M8 39
Code
690 690 720
87546 87547 87548
1520 1545 2275
87549 87550 87551
Options: FPM diaphragm order H0 VMB*** PTFE diaphragm order H0 VMC*** *Note: 2½", 3" and 4" are spigot ended.
FK Butterfly valves Glass reinforced polypropylene with ABS disc and EPDM seals Lever operated Size
DN
6 8
150 9 134 225 330 110 70 3850 8 200 9 161 272 420 122 71 6750 8
PN
B2
Options: FPM seals order H0 FKB***
B3
C
C1
Z
gms
U
U = No. of holes
Note: Lugged versions available to special order. Please refer to our Valve Department for further details.
30
Code 90779 90780
SuperFLO ABS
Cobra pipe clips Polypropylene Size
D
G
gms
Code
3/8
– 35 25
19
16
M.4/3BA/No 8 7
98327
½
– 35 30
14
16
M.5/1BA/No 10 8
92346
¾
– 35 35
16
17
M.5/1BA/No 10 11
92347
1
– 40 40
17
17
M.5/1BA/No 10 14
92348
1¼ 75 45 45
20
20
M.5/1BA/No 10 21
92349
1½ 85 50 50
22
21
M.6/0BA/No 10 30
92350
M.6/0BA/No 10 42
92351
A C D G
B
A
B
C
Bolt/Screw size
2
102 60 60
19
21
3
148 80 90
39
31
M.8
121
92352
4
171 90 96
36
35
M.8
185
92353
M.8
330
92354
6 243 170 150 40 40
Clips of size 1¼" and above are fitted with retaining strap. Bolts/screws not supplied.
Saddle clips Polypropylene
Size C F G
E
C
E
F
G
gms
Code
3/8
13 37
–
14
M.4/3BA/No 8 3
90793
½
18 41
–
14
M.4/3BA/No 8 4
90794
Bolt/Screw size
¾
21 45
–
16
M.5/2BA/No 10 6
90795
1
23 56
–
16
M.5/2BA/No 10 7
90796
1¼
29 65
–
16
M.5/2BA/No 10
90797
1½
34 67
–
16
M.5/2BA/No 10
12
90798
2
38 87
–
22
M.6/0BA/No 12
25
90799
3
50
122 8
34
4 65 156 13 38
11
M.10/3⁄8UNC 45 90800 M.10/3⁄8UNC 70 90801
Backing plate shown dotted supplied with 3" and 4" only. Bolts/screws not supplied. Bolt holes in 3" and 4" clips are not countersunk.
One-step solvent cement
Litres
gms Code
0.5 550
1.0
1100
90802 90803
Only Durapipe ABS solvent cement and Durapipe MEK cleaner should be used for jointing of Durapipe ABS pipework systems.
MEK Cleaner
Litres
gms Code
0.5 500
90804
Only Durapipe ABS solvent cement and Durapipe MEK cleaner should be used for jointing of Durapipe ABS pipework systems.
31
SuperFLO ABS
SuperFLO ABS Jointing Guide Solvent cement welding offers a simple and quick means of constructing high integrity, leak-free joints. The solvent cement operates by chemically softening the joint surfaces. Joint integrity will be greatly reduced if these surfaces are not clean and properly prepared. Durapipe SuperFLO ABS solvent cement must be used. The jointing procedure detailed below must be followed. When using ‘One-step’ solvent cement, it is not necessary to abrade pipe or fitting (unless making a joint on to old ABS pipe). No attempt should be made to increase the clearance between the pipes and fittings.
Procedure
4. Ensure joint surfaces are clean and free from moisture. Clean surfaces thoroughly with Durapipe MEK Cleaner using lint free cloth/paper towel.
1. The pipe must be cut clean and square. A suitable wheel cutter will eliminate swarf. As an alternative (and on larger sizes) a carpenters saw should be used, however this may create dust and swarf which can enter the system.
5. Using a clean brush apply cement to the pipe and fitting. The joint surfaces should be completely covered by cement.
2. Chamfer the end of the pipe using a coarse file or suitable chamfering tool. The chamfer should be approximately 45° by 3mm to 5mm depending on the pipe size. Reducing bushes should also be chamfered (unless where a moulded chamfer is included).
3. Mark the pipe a known distance from the end and clear of the area to be cleaned. This mark should be used to confirm full insertion of pipe into socket of fitting.
32
Cement should be applied using an appropriate size brush and tin of cement. It is important to apply cement quickly to enable assembly without excessive force being required. When applying cement with brush, the size of the brush should be approximately half the size of the pipe to be jointed - brush size up to 2½" (63mm) for 0.5 litre and up to 3" (75mm) for 1 litre tins.
6. Immediately after applications of cement, push pipe fully home into the fitting. Do not twist. Hold the pipe and the fitting for times varying from a few seconds on sizes 3/8" or 16mm up to 1 minute on size 315mm. The slight taper moulded into the fitting may otherwise cause it to slide off the pipe with consequent loss of joint strength. Application of the correct amount of cement will result in a neat bead of cement at the edge of the fitting and at the edge of the pipe. Excessive deposits inside the fittings must be avoided as these can weaken the wall, particularly on smaller sizes. When working under cold conditions make sure the joints are free from frost and moisture.
SuperFLO ABS
9. Do not disturb a joint for least 10 minutes. On larger sizes do not subject the joint to bending or twisting forces for at least 4 hours. When making subsequent joints, which can be done without waiting, take care not to transmit forces to freshly made joints in the system. 10. Replace lids on containers.
CAUTION • DO NOT use near naked flames • DO NOT smoke in the working area
7. Wipe off excess cement from the outside of the joint.
• DO NOT use in confined spaces • DO NOT joint in the rain or wet conditions • DO NOT use dirty brushes • DO NOT use dirty or oily cleaning cloths • DO NOT use the same brushes for different cements • DO NOT dilute or decant SuperFLO ABS solvent cement • Follow safety instructions on Durapipe solvent cement and Eco-cleaner containers • Always wear appropriate personal protective equipment
8. Using the mark previously made, check that the pipe has been fully inserted.
Notes 1. The integrity of SuperFLO ABS systems may be affected if SuperFLO ABS One-step solvent cement and Durapipe MEK Cleaner are not used. Durapipe UK disclaims responsibility for any SuperFLO ABS system constructed with any other cement or not fabricated in accordance with the instructions herein. 2. Use the appropriate size of solvent cement tin/container and method of application for the size of pipe and fitting to be assembled. 3. To achieve the correct speed of application on sizes 5"/140mm and above, cement should be applied simultaneously to pipe and fitting, by two people.
Drying times The drying times will vary with fit, amount of solvent cement applied, ambient temperature and working pressure. It is recommended that, wherever possible, joints of sizes up to 8"/225mm are allowed to dry for at least 24 hours, and sizes 250mm and 315mm for at least 48 hours.
An indication of the number of joints to be made per litre of cement is as follows: mm
inch
Recommended container size
Joints per litre ABS
These guidelines are based on an ambient temperature of between 10°C to 40°C. Longer drying times will be required at lower and higher ambient temperatures.
16 - 32
3/8 - 1
0.5 Litre
400
40 - 63
1¼ - 2
0.5 Litre
200
It is recognised that there will be occasions when the system will need to be put into service within a few hours of being made. A rough but safe working guide where the ambient temperature is between 10°C to 40°C and the contents temperature does not exceed 20°C is as follows:
75 - 110
2½ - 4
0.5 Litre
70
125 - 140
5
1 Litre
20
160 - 225
6-8
1 Litre
10
1 Litre
5
Size Range
Up to 2½" 75mm
Drying Time 0.5 hour / bar
Size
250 - 315
3" to 4" 90mm to 125mm
5" & 6" 140mm & 160mm
8" 200mm & 225mm
250mm & 315mm
1.0 hour / bar
1.5 hours / bar
2.0 hours / bar
48 hours minimum
Note - minimum drying period should never be less than 1 hour. Drying times should be extended at temperatures below 20ºC. Solvent cement joints should not be made below 0ºC.
33
SuperFLO ABS
Comparison of SuperFLO ABS Imperial and Metric Sized Pipe Please refer to the pipe section in this brochure for pipe sizes available from Durapipe UK.
Tabulated below is a comparison of imperial and metric sized SuperFLO ABS pipe. They are produced to different standards, but can be joined together using flanges or adaptors.
Threaded systems Imperial system Class T ABS pipe can be machined to BSP parallel or BSP taper thread forms. Metric pipe is not produced with an outside diameter suitable for threading.
The systems are also designated differently; the imperial system refers to the nominal bore size; the metric system relates to the outside diameter. Both systems are produced with the outside diameter as the controlled dimension. This enables the same fitting of a particular size to be joined to all classes of pipe in that size.
Imperial System (BS 5391) Size (nominal bore) (imperial)
Minimum mean outside diameter (mm)
3/8 ½ ¾
Metric System (ISO 15493)
Minimum wall thickness (mm)
Size outside diameter (mm)
Minimum mean outside diameter (mm)
Minimum wall thickness (mm) PN10
3.4
16
16.0
1.4
1.9
3.5
20
20.0
1.5
2.4
3.5
25
25.0
1.8
-
3.0
4.2
32
32.0
2.0
2.4
-
3.8
5.1
40
40.0
2.5
2.7
-
4.4
5.8
50
50.0
3.2
-
3.4
-
5.4
7.0
63
63.0
4.0
-
4.7
-
-
-
75
75.0
4.7
88.7
-
5.0
-
8.06
-
90
90.0
5.7
114.1
-
6.4
-
10.3
-
110
110.0
6.9
-
-
-
-
-
-
125
125.0
7.9
5
140.0
-
8.8
-
-
-
140
140.0
8.8
6
168.0
-
9.4
12.3
-
-
160
160.0
10.0
Class B
Class C
Class D
Class E
Class T
17.0
-
-
-
1.6
21.2
-
-
-
26.6
-
-
-
1
33.4
-
1.9
1¼
42.1
-
1½
48.1
-
2
60.2
2½
75.0
3 4 -
-
-
-
-
-
-
-
200
200.0
12.5
8
218.0
-
12.2
-
-
-
225
225.0
14.1
-
-
-
-
-
-
-
250
250.0
15.6
-
-
-
-
-
-
-
315
315.0
19.7*
2½” and 5” pipes are PN10 rated. *315mm is rated at PN8. Properties guide Chemical resistance and performance data
Typical applications
Unsuitable for the following uses
Sizes and jointing information
Moderately strong mineral acids
Chilled water
Applications over 60ºC
Metric: 16mm to 315mm OD
Caustic and ammoniacal solutions
Low temperature brine
Bleaches
Imperial: 3/8" to 8" NB
Most inorganic salt solutions
Potable water
Solvents
Jointed by solvent cement welding
Some detergents
Process water
Domestic hot water
Threaded fittings available
Temperature range -40ºC to +60ºC
Flammable substances
Note: Temperatures given are for guidance only, please check before specifying.
DURAPIPE UK MANUFACTURE FULLY MATCHED PIPEWORK SYSTEMS. AS A RESULT WE DO NOT RECOMMEND THE USE OF NON-DURAPIPE PRODUCTS INCLUDING BACKING RINGS, GASKETS, SOLVENT CEMENT AND CLEANER.
INSIST ON DURAPIPE.
34
SuperFLO ABS
35
Double Containment Systems Safety and environmental concerns are top priorities on today’s industrial agenda. Reduction of emissions, energy conservation and prevention of ground water contamination are some of the areas where regulations are increasingly defining an important line between utilisation and exploitation of our planet’s resources. For most common chemical-waste or process applications, Vinidex offers systems that are both simple yet highly advanced state-of-the-art technologies. These systems utilize pre-assembled components that guarantee reliability, ease of installation, fewer joints (up to 40% less) and quick delivery. Certain environments demand fail-safe systems. No leaks. No risk. We understand the complexity of design and installation for demanding double containment applications.
36
For more than 30 years, Guardian systems have been the benchmark in pressure and drainage double containment. Guardian systems are available in tough industrial grade PVC and even tougher high temperature CPVC. For instant leak detection of overhead piping, Clear-Guard clear PVC containment pipe is also available. Guardian’s patented Centra-Lock design reduces the required joints by 40 - 60% compared to conventional double containment Systems.
Clear-Guard’s fail-safe, fully pressure rated clear containment system allows for easy detection of leaks and eliminates the risks associated with piping aggressive chemicals overhead. ClearGuard utilizes Guardian’s patented Centra-Lok fitting design, which reduces the required joints by 40-60% compared to conventional double containment systems. Fittings are available in clear or opaque containment fittings.
Custom-designed and fabricated double containment systems including dissimilar material systems, CustomGuard is unlike other systems that try to run everything through the same material. For applications with more demanding mechanical, chemical and/or thermal requirements, we have developed our CustomGuard offering. CustomGuard includes a variety of different system choices ranging from Fluoropolymers (e.g. PVDF), Thermosets (FRP); and carbon and stainless steel to hybrid combinations.
Although many different leak detection systems are available on the market today, only the CentraGuard patented electronic low point leak-detection system offers a combination of advanced features including versatility; customization; and lower material, installation and maintenance costs when compared to cable leak detection. Centra-Guard is suitable for above-ground suspended pipeline applications, with sensors housed in a saddle-type clamp as well as underground pipeline systems with drip leg assembly.
Our PAL-AT cable leak detection is a microprocessor based system that offers continuous cable leak detection. The system is fully automated and ideal for buried double containment piping applications that require exact leak location. Our PAL-AT continuous cable leak detection system compliments our Centra-Guard electronic low point leak detection system and adds extra versatility to our extensive double containment offering. Product available on request. Contact your Vinidex representative for further information.
Applications that require such materials are obviously complex, each demanding expertise and specialized knowledge to design an effective system. The CustomGuard option includes material selection, design, specification support (if needed) and fabrication of preassembled spooled pieces to minimize installation time and field joints. In many situations double containment protection by itself may not be enough. In these applications it is critical that a leak is immediately detected and located.
37
Double Containment Systems
CHOOSE FROM A WIDE RANGE OF SYSTEM OPTIONS Vinidex offers an extremely wide array of materials and sizes. You can specify virtually any piping material to create a system that contains whatever corrosive or hazardous substance your application handles. If you don’t see what you need listed here, call us! Other systems or sizes may be available, or we may have suggestions for substitutions. SYSTEM Carrier
38
Carrier SIZE inches
Containment
SYSTEM Carrier
Containment
Carrier SIZE inches
PVC 80
PVC 80
½ - 12
S40 A53 BLK SW
FRP
½-2
PVC 80
PVC 40
½ - 12
S40 A53 BLK SW
PVC 80
½-2
PVC 40
PVC 40
½ - 12
S80 A53B CS SW
PVC 80
½-2
PVC DWV
PVC DWV
1½ - 12
S10 T304L SS BW
PVC 80
½-8
PVC 80
CS SCH 10
½ - 12
S10 T304L SS BW
PVC 40
½-8
CPVC 80
CPVC 80
½-8
S10 TO304L SS BW
CPVC 80
½-8
CPVC 80
PVC 80
½ - 12
S10 T304L SS BW
FRP
½ - 12
CPVC 80
PVC 40
½ - 12
S10 T304L SS BW
S10 T304L
½ - 12
CPVC 80
CS SCH 10
½ - 12
S40 T316L SS BW
PVC 80
½-8
NAT PP 80
PVC 80
½-2
S40 T316L SS BW
CPVC 80
½-8
NAT PP 80
PVC 40
½-2
S40 T316L SS BW
FRP
½ - 12
RED PVDF 80
CPVC 80
½-2
S40 T304L SS SW
PVC 80
½-2
RED PVDF 80
PVC 80
½-2
S40 T304L SS SW
PVC 40
½-2
NAT PVDF 80
PVC 80
½-2
S40 T304L SS SW
CPVC 80
½-2
ENFUSION PP
PVC DWV
½-6
S40 T304L SS SW
FRP
½-2
S40 A53B CS BW
PVC 80
½-8
S10 T316L SS SW
PVC 80
½-2
S40 A106B CS BW
PVC 80
½-8
S10 T316L SS SW
CPVC 80
½-2
S80 A106B CS SW
PVC 80
½-8
S10 T316L SS SW
FRP
½-2
S40 A53B CS BW
FRP
½ - 12
S40 T304L SS BW
PVC 80
½-8
S40 A106B CS BW
FRP
½ - 12
S40 T304L SS BW
PVC 80
½-8
S80 A106B CS SW
FRP
½-2
S40 T304L SS BW
CPVC 80
½-8
S40 A53B THRD
PVC 40
½-2
S40 T304L SS BW
FRP
½ - 12
S40 A106 SMLS BW
PVC 40
½-8
S10 T316L SS BW
PVC 80
½-8
S40 A53 BLK BS
PVC 40
½-8
S10 T316L SS BW
CPVC 80
½-8
S80 A53 BLK SW
PVC 80
½-2
S10 T316L SS BW
FRP
½ - 12
S80 A53 BLK SW
FRP
½-2
S10 T304L SS SW
PVC 80
½-2
S40 A53 BLK SW
S40 A53 BLK
½-2
S10 T304L SS SW
PVC 40
½-2
S40 A106B CS SW
PVC 80
½-8
S10 T304L SS SW
CPVC 80
½-2
S80 A53B CS BW
PVC 80
½-8
S10 T304L SS SW
FRP
½-2
S80 A106B CS SW
PVC 80
½-8
S10 T304L SS SW
S10 T304L
½-2
S40 A106 CS SW
FRP
½-2
S40 T316L SS SW
PVC 80
½-2
S80 A53B CS BW
FRP
½ - 12
S40 T316L SS SW
CPVC 80
½-2
S80 A106B CS BW
FRP
½-2
S40 T316L SS SW
FRP
½-2
S40 A53B THRD
FRP
½-2
HARD COPPER
PVC 40
½-4
S40 A53 BLK CS
S40 A53 BLK CS
½ - 12
HARD COPPER
3000 FRP
½-4
S40 A53 BLK SW
PVC 40
½-2
39
Acid Waste Piping Systems
40
Safe chemical drainage
Vulcathene boasts over 60 years proven performance in the laboratories of thousands of schools, universities, hospitals and research facilities around the world ... proof of its very high reliability for safe chemical drainage. Vulcathene is specified worldwide and proven as the world leading solution for chemical waste drainage. It has two easy jointing methods – Mechanical or Enfusion. Fittings are injection moulded and purpose designed.
41
Vulcathene PP
W001 Pipe Produced in nominal internal diameters of 38mm, 51mm, 76mm, 102mm and 152mm (Enfusion only), Vulcathene pipes are supplied in standard 4m lengths. 1½" 2" 3" 4" 6" Nominal internal diameter 38mm 51mm 76mm 102mm 152mm Nominal external diameter 48.3mm 60.3mm 89.0mm 114.3mm 168.3mm Kg/m 0.43 0.58 1.25 1.63 4.34 Vinidex Code 90187 90188 90189 90190 90191
504 Waste The range of 1¼", 1½", and 2" BSP threaded wastes are produced with flange widths of 60, 73 and 85mm to suit ceramic, porcelain, metal or plastic sink outlets. Slotted wastes are available for use where the waste has to accept an overflow. With an integral grating the waste is supplied with a plug ready to accept a chain fastening. Both the 1¼" and 1½" waste outlets are available in all flange diameters and either 89mm or 102mm lengths; the 2” waste outlet is available in 85mm flange diameter and 102mm length only. Unslotted waste outlets are supplied with one waste gasket; slotted wastes are supplied with two waste gaskets. When ordering please indicate - a. Waste diameter; b. Flange diameter; c. Whether slotted or unslotted required. Vinidex Code A (mm) Unslotted Waste 90228 60 90230 73 90232 85 90234 60 90236 73 90238 85 90240 85 gms 1¼"-65; 1½"-75; 2"-90
B (mm)
C (inch)
D (mm)
89 102 102 89 102 102 102
1¼ 1¼ 1¼ 1½ 1½ 1½ 2
3 3 3 3 3 3 3
Vinidex Code A (mm) Slotted Waste 90229 60 90231 73 90233 85 90235 60 90237 73 90239 85 90241 85 gms 1¼"-65; 1½"-75; 2"-90
B (mm)
C (inch)
D (mm)
89 102 102 89 102 102 102
1¼ 1¼ 1¼ 1½ 1½ 1½ 2
3 3 3 3 3 3 3
507 Standing Waste Tube Standing waste tubes are available in three lengths and the diameters are in relation to the need to fit 1¼", 1½", and 2" BSP threaded 504 series wastes. If required they can be supplied with a hanging loop. 51mm size supplied in 225mm length only. 32mm and 38mm supplied in 140mm and 178mm lengths only.
42
Vinidex Code 90242 90244 90246 90248 90250
A (mm) B (mm) 140 32 178 32 140 38 178 38 225 51
Vinidex Code Fitted with hanging loop 90243 90245 90247 90249 90251
A (mm)
B (mm)
140 32 178 32 140 38 178 38 225 51
Vulcathene PP
508 Plug & Chain Assembly Comprising a 450mm length of stainless steel oval link chain, with a screw stay, the plug and chain assembly is available to fit either 1¼", 1½", or 2" BSP No. 504 series waste fittings. Vinidex Code Size (inch) 90254 1¼ 90252 1½ 90253 2 gms 1¼"-40; 1½"-44; 2"-50
509 Overflow Assembly The range of 509 overflow assemblies are suitable for installation with a 38mm slotted waste and any sink illustrated in this catalogue. They comprise of an overflow collar connected by a flexible hose to the overflow bend. Because of the varying requirements for placement of the overflow in the side of the sink we recommend that a hole of 42mm diameter be cut in the side of the sink to take the overflow bend. The overflow is extendable from 9" to 22". Cat. No. 509 A 60mm B 48mm gms 65 Vinidex Code 90255
501 Small Circular Drip Cup The range of 501 small circular drip cups, come with an integral grating and a wall thickness of 3mm. The small circular drip cup has steeply sloping sides to minimise splashing and the 8mm wide rim gives it stability when top mounted in the working surface. With an opening diameter of 86mm and depth of 73mm it is supplied complete with hose restraining plug and backnut. Cat. No. 501 A 102mm B 136mm C 1½" BSP E 5mm F 6mm G 76mm Vinidex Code 90227
500 Large Circular Drip Cup The range of 500 large circular drip cups come with an integral grating and a wall thickness of 3mm. The large circular drip cup is designed for top mounting. With a top opening diameter of 146mm it is 114mm deep and the 11mm wide rim gives it stability when top mounted in the working surface. It is supplied complete with a backnut and hose restraining plug. Cat. No. 500 A 168mm B 165mm C 1½" BSP E 8mm F 11mm G 114mm Vinidex Code 90226
43
Vulcathene PP
497 Small Oval Drip Cup The range of 497 small oval drip cups are moulded with a 3mm thick wall and have an opening of 166mm x 90mm x 143mm deep. The 6mm wide rim gives it stability when top mounted in the working surface. It has an integral grating, is designed for top mounting and is supplied complete with backnut. Cat. No. 497 A 178mm B 216mm C 1½" BSP D 102mm E 6mm F 6mm G 143mm Vinidex Code 90224
A = length D = width
499B/499T Large Oval Drip Cup The range of 499 Large Oval Drip Cups are moulded with a 3mm thick wall, offering a choice of 2 alternative flange fixings. Moulded with deeply curved bowls, they have integral gratings and are supplied complete with backnuts and a hose restraining plug. The 499B and 499T are designed for top mounting. Cat. No. 499B 499T A 264mm 305mm B 225mm 225mm C 1½" BSP 1½" BSP D 111mm 152mm E 6mm 6mm F 13mm 32mm G 161mm 161mm Vinidex Code 90225 90223
A = length D = width
601 Sink The 601 sink is extremely robust and has a self-draining base. Its recessed outlet will accept the flange of the 1½" BSP 504 non-overflow threaded outlet but, if required, a 509 overflow assembly can be fitted. These sinks are designed for mounting on the underside of work surfaces. Cat. No. 601 A 492mm B 171mm C 76 mm D 241mm H 32mm gms 1030 Radius 36mm Vinidex Code 90204
A = length D = width
602 Sink The 602 sink is extremely robust and has a self-draining base. Its recessed outlet will accept the flange of the 1½" BSP 504 non-overflow threaded outlet but, if required, a 509 overflow assembly can be fitted. These sinks are designed for mounting on the underside of work surfaces. Cat. No. 602 A 552mm B 231mm C 74mm D 400mm E 152mm H 35mm gms 2668 Radius 35mm Vinidex Code 90205
44
A = length D = width
Vulcathene PP
604 Sink Available in three sizes the 604 range of sinks are extremely robust and have a self-draining base. The 76mm recessed outlet will accept the flange of the 1½" BSP 504 non-overflow threaded outlet but, if required, a 509 overflow assembly can be fitted. These sinks are designed for mounting on the underside of work surfaces, the 48mm wide top rim, which gives rigidity, has a recess flange to accept the self-adhesive sealing strip supplied with each sink. Cat. No. 604/1 604/2 604/4 A 343mm 445mm 492mm B 140mm 140mm 165mm C 76mm 76mm 76mm D 288mm 343mm 419mm E 152mm 152mm 152mm H 48mm 48mm 41mm gms 2765 Radius 40mm 40mm 40mm Vinidex Code 90182 90183 90184
A = length D = width
605/1 Trough This trough has a self-draining base which incorporates a 76mm recessed outlet to accept a 1½" BSP 504 non-slotted threaded waste. These troughs are designed for mounting on the underside of work surfaces. Each trough is supplied with a self-adhesive sealing strip which, when positioned in the recess in the trough lip, will form a watertight seal between the trough and the work surface. Cat. No. 605/1 A 403mm B 111mm C 76mm D 190mm H 38mm Radius 36mm Vinidex Code 90185
A = length D = width
603 Running Trough Fabricated to customers specific requirements the running trough is manufactured with 3mm thick walls and is supplied complete with waste outlet - as specified - and supporting framework. Cat. No. A B C Made To Order
603 127mm 210mm 1½" BSP 2" BSP
W681 Dilution Recovery Trap Easily emptied, by unscrewing the base from the trap, this large capacity anti-siphonic dilution recovery trap has a 76mm liquid seal and holds 2.3 litres. The 1½" BSP inlet includes a loose nut coupling for connection to a waste outlet or drip cup tail. The trap is supplied with a nut and olive to enable it to be ‘P’ trap configured for 38mm pipe. The addition of a W291 38mm bend will change the configuration to an ‘S’ trap. Cat. No. W681 A 86mm B 325mm C 270mm D 133mm E 1½" Mechanical thread F 1½" BSP gms 480 Vinidex Code 90169
45
Vulcathene PP
W691 Dilution Recovery Trap (Glass Base) The 691 trap has a total capacity of 2.3 litres and a 76mm liquid seal. The clear base of heat resistant, borosilicate glass makes this an ideal choice for use in waste systems which have to cope with large quantities of solid waste matter. The trap allows the volume of solids collected to be quickly assessed and, where necessary, cleared, before they can cause any damage to the system. It also allows the identification and recovery of valuable solids. In order to remove the dilution chamber from the trap body, the glass unit should be unscrewed complete with its flange assembly. The 1½" BSP inlet includes a loose nut coupling for connection to a waste outlet or drip cup tail. The trap is supplied with a nut and olive to enable it to be ‘P’ trap configured for 38mm pipe. The addition of a W291 38mm bend will change the configuration to an ‘S’ trap. Cat. No. W691 A 86mm B 314mm C 254mm D 229mm E 1½" Mechanical thread F 1½" BSP gms 2390 Vinidex Code 90170
When installed it is important to support the underside of the trap (at least 76mm above the floor) to avoid weight strain on the pipework and connections.
W561 Anti-Siphon Bottle Trap Retaining its seal under the most demanding conditions this trap is completely dependable and is ideal for the most severe conditions. With a 76mm liquid seal, the base can be unscrewed from the body for easy cleaning. Provided with a 1½" BSP loose nut coupling for screwing to waste or drip cup tails, the ‘P’ outlet is supplied with nut and olive to take 38mm Vulcathene mechanical pipe. When required a W291/ L291A 38mm bend will convert it to an ‘S’ trap. Cat. No. W561 A 86mm B 203mm C 143mm D 1½" BSP E 1½" Mechanical thread F 89mm gms 300 Vinidex Code 90160
W571 Anti-Siphon Bottle Trap (Glass Base) Retaining its seal under the most demanding conditions this trap is completely dependable and is ideal for the most severe conditions. With a 76mm liquid seal, the base can be unscrewed from the body for easy cleaning. Provided with a 1½" BSP loose nut coupling for screwing to waste or drip cup tails, the ‘P’ outlet is supplied with nut and olive to take 38mm Vulcathene mechanical pipe. When required a W291/ L291A 38mm bend will convert it to an ‘S’ trap. Cat. No. W571 A 86mm B 222mm C 162mm D 1½" BSP E 1½" Mechanical thread F 89mm gms 923 Vinidex Code 90161
46
The clear base of heat resistant, borosilicate glass makes this an ideal choice for use in waste systems which have to cope with large quantities of solid waste matter. The trap allows the volume of solids collected to be quickly assessed and, where necessary, cleared, before they can cause any damage to the system. It also allows the identification and recovery of valuable solids.
Vulcathene PP
W612 Dilution Recovery Trap With a 4.5 litre capacity and a 76mm trap seal the W612 is particularly useful for those situations where under-bench height is limited. When cleaning out the unit, union nuts on the lid should be disconnected, the dip tubes withdrawn and the interior of the dilution chamber carefully flushed out. No attempt should be made to separate the lid from the dilution chamber. For a ‘P’ outlet, a 51mm nut and olive is supplied, and for an ‘S’ outlet, add a W292 51mm bend. Where it is intended to use the unit as a dilution chamber only, the dip tubes should be omitted. The unit is supplied with dip tubes, nuts, olives and blanking off plug. (Additional dip tubes and blanking off plugs can be ordered separately). Cat. No. W612 A 230mm B 121mm C 318mm D 244mm E 168mm gms 2250 Vinidex Code 90164
910G Dilution Recovery Trap (Glass Base) With a 4.5 litre capacity and a 76mm trap seal the 910G, with its clear base of heat resistant, borosilicate glass allows the volume of solids collected to be quickly assessed and, where necessary, cleared. It also allows the identification and recovery of valuable solids. The new 910G is supplied with a removable lid & gasket seal, both held in place by a stainless steel clamp which can be easily removed for access & maintenance. Outlet connection is 51mm, with nut & olive supplied. Dip tubes, vertical inlets, horizontal inlets and blanking off plugs should be ordered separately. Cat. No. 910G A 208mm B 246mm C 265mm D 156mm gms 4010 Vinidex Code 90257
W915 Clay Trap With a 20 litre capacity the 552 x 400 x 270mm deep clay trap incorporates inlet, and outlet connections at opposite ends, which accept W151 38mm FI BSP connectors. The outlet connection has a 76mm liquid seal and the lid, which has a sealing ring, is retained in position with fourteen wing nuts. Cat. No. W915 A 552mm B 76mm C 38mm D 400mm E 270mm F 171mm gms 8900 Vinidex Code 90179
47
Vulcathene PP
Trapped Floor Gully The 4.5 litre trapped floor gully is fabricated from beige grey polypropylene and has a 76mm liquid seal. The removable grating gives easy access to the interior for cleaning. The gully has a 76mm plain ended outlet for either Mechanical or Enfusion jointing. Additional side or back inlets in positions A, B or C (as indicated) can be supplied to order. Note: Vulcathene floor gullies are fabricated to order. Nom. Size 4.5 litres A 250mm L 320mm D 89.0mm (Outside Diameter) gms 3420 Made To Order
PC91 Pipe Clip Of snap-on type these clips retain the pipe securely in place while allowing lateral movement of the pipe caused by fluctuations in thermal conditions. Note: When 76mm and 102mm pipe are installed in long vertical runs considerable strain may be caused by thermal movement. In such conditions metal brackets should be used to retain the pipe, ie. Munson Ring. Cat. No. Nom. Size A B C gms Vinidex Code
91 38mm 51mm 38mm 44mm 60mm 76mm 19mm 19mm 32 52 90216 90217
76mm 102mm 67mm 89mm 111mm 140mm 32mm 32mm 82 120 90218 90219
W916 Flexible Connector Standard flexible connectors manufactured from polypropylene for use with mobile fume cupboards. The ends are pre-grooved with nut and olive supplied. Vinidex Code Size Length (m) 90260 38mm 1 90263 38mm 1.5 90261 38mm 2 90262 38mm 3 Note: Other lengths can be supplied to order
W465 Clamp Saddle Clamp saddles enable easy connection of new branch pipes to existing Vulcathene stacks. The saddles have BSP female threaded outlets, nitrile seals, zinc plated hardware and are a charcoal grey colour supplied in four sizes. 76mm saddles are supplied with 4 x bolts; 102mm saddles with 6 x bolts. For connection to 38mm and 51mm Vulcathene pipes use Vulcathene Mechanical or Enfusion male BSP adapters. (See clamp saddle installation information on Page 47) Cat. No. Sizes:
48
W465 Vinidex Code 102mm x 2" BSP gms: 540 90210 102mm x 1½" BSP 500 90211 76mm x 2" BSP 440 90212 76mm x 1½" BSP 430 90213
A
B C
Vulcathene PP
W450 Air Admittance Valve Air admittance valves enable Vulcathene stacks to be terminated inside the building thereby avoiding costly roof penetration. They are designed to prevent the release of foul air whilst admitting air under conditions of reduced pressure in discharge pipes preventing water seals in traps from being drawn. The valves also contribute to the ventilation of the main drain to which the discharge stack incorporating the valve is connected.
C
A
The Vulcathene air admittance valve is designed to suit 102mm Vulcathene pipe and incorporates a rubber finned tail for internal pipe connection and a removable screw cap for maintenance access.
B
To connect to a 76mm Vulcathene stack use a 102mm/76mm reducer and insert the valve into the 102mm socket. The AAV is approved to BS EN 12380 (B1) Cat. No. W450 Sizes: 102mm A 245mm B 60mm C 135mm gms 872 Vinidex Code 90214
W50 Anti-Siphon Unit Anti-siphon units are designed to prevent the release of foul air whilst admitting air under conditions of induced or self-siphonage in discharge pipes preventing water seals in traps from being drawn. The W50 is suitable for connection to 51mm Vulcathene pipe and incorporates a rubber seal which must first be inserted into the pipe followed by the anti-siphon unit. The anti-siphon unit is approved to BS EN12380 (A11)
A B
Cat. No. W50 Sizes: 51mm A 61mm B 22mm C 36mm Vinidex Code 90215
C
Galvanised Support Channel
W641/W642 Horizontal Inlet
A galvanised metal support channel, supplied in standard 2.5 metre lengths, should be used where Vulcathene pipework requires continuous support.
For use with 910G Dilution Recovery Traps to make a horizontal pipe connection.
Sizes:
Vinidex Code 38mm 90206 51mm 90207 76mm 90208 102mm 90209
Cat. No. W641 W642 gms 148 207 Vinidex Code 90165 90166
Vulcathene Lubricant
Glass Dip Tube
Supplied in 200g pots, Vulcathene lubricant should be applied to the threads of fittings before making a mechanical joint.
For use with 910G Dilution Recovery Traps
Vinidex Code
Vinidex Code
V5900002
90259
49
Vulcathene PP
W651/W652 Vertical Inlet
Blanking Off Plug
For use with 910G Dilution Recovery Traps to make a vertical pipe connection.
For use with 910G Dilution Recovery Traps
Cat. No. W651 W652 gms 97 135 Vinidex Code 90167 90168
Vinidex Code
90258
UniCollar® Fire Protection UniCollar is a unique method of protecting Vulcathene pipes which pass through fire rated walls and floors. The system is supplied in continuous strip form which is cut to length and attached to the element using ready-made clips. These clips fit into the pre-punched slots on the strip. UniCollar is packed in a box which contains 2250mm length of collar or 150 segments. The box has installation details on one face. The collar is designed so that it can be cut and snapped in segments of 15mm. One box is the equivalent of 5 x 102mm (114.3mm OD) Vulcathene collars. Vinidex Code
V468100
DC95/DC115 Flexible Drain Coupling For connecting 76mm and 102mm Vulcathene stacks to underground drainage systems of other materials where a flange connection is not available. Flexible drain couplings, with nitrile sleeves, incorporate medium duty stainless steel clamping bands at either end. Cat. No. DC95 Size range (mm) 80-95 Width (mm) 100 ‘T’ (mm) 7 Application 75mm (3") ABS 75mm Cast Iron 75mm Ductile Iron gms 402 Vinidex Code V100DC95
DC115 100-115 100 7 100mm PVC-U 100mm PE 100mm Stainless Steel 435 V10DC115
AC1221/AC1361 AC5144/AC1362 Flexible Adaptor Coupling For connecting 76mm and 102mm Vulcathene stacks to underground drainage systems of other materials where a flange connection is not available. Flexible adaptor couplings have a stepped moulded nitrile sleeve with different diameters at each end to enable pipes of differing outside diameters to be jointed economically and quickly without the use of bushes. The sleeve is fitted with two stainless steel clamping bands by which they are secured to the pipe ends. Cat. No. AC1221 AC1361 AC5144 AC1362 Size range A/B 110-122/80-95 121-136/80-95 110-125/100-115 121-136/100-115 (mm) Width (mm) 100 100 100 100 Application PVC-U Vitrified Clay Supersleeve Vitrified Clay (100mm) Cast Iron Asbestos Cast Iron Salt Glazed Supersleeve Cement Ware Salt Glazed Ductile Iron Asbestos Ware Asbestos Cement Cement gms 400 460 463 500 Vinidex Code V1AC1221 V1AC1361 90181 90180
50
Vulcathene PP
W18 92½° Bend Both ends have standard nut and olive connections. Cat. No. W181 W182 Nom. Size 38mm 51mm A 43mm 64mm gms 64 113 Vinidex Code 90099 90100
W183 W184 76mm 102mm 86mm 100mm 343 625 90101 90102
W29 92½° Loose Nut Sweep Bend One end has the standard nut and olive connection whilst the other has a captive nut for connection to threaded units. Cat. No. Nom. Size A B gms Vinidex Code
W291 W292 W293 W294 38mm 51mm 76mm 102mm 54mm 64mm 87mm 104mm 65mm 93mm 136mm 167mm 68 109 338 613 90133 90134 90135 90136
W19 135° Slow Bend Both ends have standard nut and olive connections. Cat. No. Nom. Size A gms Vinidex Code
W191 W192 W193 W194 38mm 51mm 76mm 102mm 15mm 16mm 51mm 48mm 75 120 291 900 90103 90104 90105 90106
W21 135° Loose Nut Slow Bend One end has the standard nut and olive connection whilst the other has a captive nut for connection to threaded units. Cat. No. Nom. Size A B gms Vinidex Code
W211 W212 W213 W214 38mm 51mm 76mm 102mm 44mm 44mm 102mm 114mm 15mm 18mm 51mm 45mm 44 66 294 468 90112 90113 90114 90115
51
Vulcathene PP
W20 92½° Equal Sweep Tee The three equal sized ends have standard nut and olive connections. Cat. No. Nom. Size A B C gms Vinidex Code
W201 W202 W203 W204 38mm 51mm 76mm 102mm 59mm 62mm 83mm 98mm 39mm 52mm 39mm 76mm 97mm 114mm 122mm 175mm 104 160 471 860 90107 90108 90110 90111
W20 92½° Reducing Sweep Tee The two equal and one reduced sized ends have standard nut and olive connections. Cat. No. W2021 Nom. Size 51x38mm A 58mm B 45mm C 114mm gms 146 Vinidex Code 90109
W37 45° Single Wye The three equal sized ends have standard nut and olive connections. Cat. No. Nom. Size A B C gms Vinidex Code
W371 38mm 86mm 64mm 8mm 96 90141
W372 W373 W374 51mm 76mm 102mm 91mm 177mm 213mm 76mm 152mm 178mm 17mm 43mm 49mm 151 650 1087 90142 90143 90144
W38 45° Double Wye Available in all sizes. The four equal sized ends have standard nut and olive connections. Cat. No. Nom. Size A B C gms Vinidex Code
52
W381 W382 W383 W384 38mm 51mm 76mm 102mm 86mm 91mm 177mm 213mm 64mm 76mm 152mm 178mm 8mm 17mm 43mm 49mm 180 228 800 1600 90145 90146 90147 90148
Vulcathene PP
W942 90° Corner Branch The 90° Corner branch is available in size 102mm x 51mm with spigot ends for either Mechanical or Enfusion jointing. The 51mm branches are at 92½° to the main bore. Additional nuts and olives are required for Mechanical jointing unless connecting to another Vulcathene Mechanical fitting. For 38mm branch connections use Vulcathene W3921 reducers. Cat. No. W942 Sizes: 102mm x 51mm A 250mm B 114.3mm C 60.3mm D 62.9mm gms 480 Vinidex Code V1094201
°
B
.5
C
87
A D
90
°
W70 ‘U’ Bend Available in 38mm and 51mm sizes the ‘U’ bend can be combined with other standard fittings from the range to make up ‘P’, ‘S’ and Running Traps with a 76mm trap seal. In order to make up both ‘P’ and ‘S’ configurations the addition of a length of Vulcathene mechanical pipe, and a W15 coupler, to one end enables it to be connected to the waste fitting whilst the addition of a W29 loose nut sweep bend converts it into a ‘P’ trap. The addition of a further W29 make it into a ‘S’ trap. Connecting a W29 to each end of the ‘U’ bend makes up a running trap. Cat. No. ‘P’ Trap ‘S’ Trap ‘Running’ Trap Nom. Size 38mm 51mm 38mm 51mm 38mm 51mm A 219mm 259mm 235mm 273mm 199mm 231mm B 136mm 171mm 85mm 75mm 136mm 171mm C 84mm 100mm 84mm 100mm gms 140 (38mm) 236 (51mm) VinidexCode 38mm 90171 51mm 90172
Component fittings required for: 'P' Trap* 'S' Trap* Nom. Size 38mm 51mm 38mm 51mm Cat No. W151 W152 W151 W152 Cat No. W291 W292 2 x W291 2 x W292 Cat No. W701 W702 W701 W701
'Running' Trap 38mm 51mm W701 W702 2 X W291 2 x W292 - -
W16 Line Coupler For connecting equal sized pipes together. Supplied with two nuts and olives. Cat. No. Nom. Size B gms Vinidex Code
W161 38mm 3mm 29 90095
W162 51mm 3mm 46 90096
W163 W164 76mm 102mm 6mm 6mm 183 301 90097 90098
53
Vulcathene PP
W39 Reducing Coupler The six reducing couplers which cover the range all have nut and olive connections on the small diameter end while the spigot end is grooved, ready to accept the nut and olive from the fitting which is to be reduced. Cat. No. W3921 W3931 Nom. Size 51 x 38mm 76 x 38mm A 40mm 60mm gms 44 95 Vinidex Code 90149 90150
W3932 76 x 51mm 57mm 102 90151
Cat. No. Nom. Size A gms Vinidex Code
W3943 102 x 76mm 71mm 251 90154
W3941 W3942 102 x 38mm 102 x 51mm 97mm 89mm 180 186 90152 90153
W14 M.I. to Pipe Coupler With standard BSP parallel threads the W14 Pipe Coupler can be screwed direct into the F.I. fittings of metal or plastic pipes. Cat. No. W141 W142 Nom. Size 38mm 51mm A 1½" BSP 2" BSP B 6mm 6mm gms 31 53 Vinidex Code 90091 90092
W15 F.I. to Pipe Coupler With standard BSP parallel threads the W15 Pipe Coupler can be screwed directly to M.I. ends of metal or plastic pipes. The 38mm unit can be screwed to the threaded tail of a waste or drip cup when a pipe connection is required. The 51mm unit can be screwed to the threaded tail of a 51mm waste. Cat. No. W151 W152 Nom. Size 38mm 51mm A 1½" BSP 2" BSP B 3mm 3mm gms 35 52 Vinidex Code 90093 90094
W271 1¾" F.I. to Pipe Coupler Made in one size only, this fitting should be used when joining 38mm Vulcathene Mechanical pipe to 38mm Vulcathene Polyfusion pipe. It may also be screwed to the outlet of any Vulcathene Polyfusion trap to provide a connection for 38mm Mechanical pipe. Cat. No. W271 Nom. Size 38mm A 1¾" BSP B 5mm gms 32 Vinidex Code 90132
54
(W3921 only)
Vulcathene PP
W121 1¼" F.I. x 1½" M.I. BSP Reducer Note: Used when jointing the Vulcathene mechanical system to a 1¼" BSP waste tail. When making a connection to pipe a W151 38mm F.I. coupler should first be added to the outlet of a W121 reducer. Alternatively, the outlet of W121, which has a standard 1½" BSP parallel thread, will accept the connecting nut of any of the Vulcathene traps illustrated in this catalogue. Cat. No. W121 Nom. Size 38mm A 32mm gms 27 Vinidex Code 90089
W45 Glass Adaptor Used when jointing the Vulcathene mechanical system to a glass drainage system. Available in Flame Retardant Polpropylene (FRPP) only. Cat. No. Nom. Size A gms Vinidex Code
W451 38mm 28mm 37 90155
W452 51mm 31mm 63 90156
W453 W454 76mm 102mm 44mm 44mm 192 317 90157 90158
W801 Thermal Stress Relief Unit The W801 can be installed either vertically or horizontally. When installed it is important to ensure that the end with the moulded fixing clip is the outflow end of the fitting. Cat. No. Nom. Size A min A max Vinidex Code
W801 38mm 70mm 108mm 90088
W802 Thermal Stress Relief Unit The W802 can be installed either vertically or horizontally. When installed it is important to ensure that the end which forms the collar is the outflow end of the fitting. The W802 SRU is supplied with 51mm mechanical Pipe Couplers at each end. The unit must be anchored with a metal clamp which should be located round the body of the SRU, just below the ridge round the top of the collar. This allows the pipe inserted into the collar to move freely. Cat. No. W802 Nom. Size 51mm A min 149mm A max 203mm B 73mm gms 243 Vinidex Code 90222
55
Vulcathene PP
W803/W804 Thermal Stress Relief Unit The W803 and W804 unit can be installed either vertically or horizontally. When installed it is important to ensure that the spigot end is the outflow end of the fitting. The unit must be anchored with a metal clamp which should be located on top of the moulded locators round the body of the SRU, which then allows the pipe inserted into the collar to expand and contract. The body of the SRU incorporates an 0-ring seal. Cat. No. Nom. Size A B C D E gms Vinidex Code
W803 W804 76mm 102mm 196mm 215mm 117.2mm 144.5mm 110mm 141mm 101.7mm 129mm 89.7mm 115mm 575 900 90173 90174
W90 Access Pipes Correctly sited at critical points in the pipeline, access pipes simplify the clearing of blockages, inspection and thorough cleansing of the installation. With a clear flow bore, the W90 series access pipes have a bolt on cover and grooved spigot ends to accept nut and olive connection to the Vulcathene Mechanical System. Cat. No. Nom. Size A B C D Vinidex Code
W902 W903 51mm 76mm 260mm 302mm 164.2mm 164.2mm 114.4mm 114.4mm 145mm 145mm V1090201 V1090301
W904 102mm 390mm 218.6mm 138.8mm 179mm V1090401
W903/W904 Access Pipe W100 BS Table D Flange (Undrilled) This allows the removal of complete pipe sections for ease of maintenance. It can also be used when connected to another BS Table D Flange. The BS Table D Flanges should be clamped together with a nitrile gasket and 4 x M20 bolts. Cat. No. Nom. Size A B C gms Vinidex Code
W101T.D 38mm 30mm 133mm 16mm 300 90084
W102T.D W103T.D W104T.D 51mm 76mm 102mm 30mm 41mm 41mm 152mm 187mm 216mm 16mm 19mm 19mm 409 1500 2087 90085 90086 90087
W22 Olive The new flexible no heat Vulcathene olive locates into a groove, cut into the pipe using the cutting tool W26, by means of a ‘tongue’ around its inner surface. This simple, yet highly effective olive is then forced into the space between the pipe and the fitting as the nut is tightened thus forming a highly effective liquid tight seal. Cat. No. Nom. Size gms Vinidex Code
56
W221 38mm 2 90116
W222 51mm 3 90117
W223 W224 76mm 102mm 51 91 901178 90119
Vulcathene PP
W23 Nut Vulcathene nuts are used in conjunction with the Vulcathene olive to make a watertight joint. Every Vulcathene Mechanical fitting is supplied complete with Vulcathene nuts. We recommend that Vulcathene lubricant is smeared on the thread to facilitate tightening of the joint using the purpose-designed W36 spanner. Cat. No. Nom. Size A B gms Vinidex Code
W231 W232 W233 W234 38mm 51mm 76mm 102mm 67mm 83mm 134mm 162mm 21mm 25mm 33mm 35mm 58 100 250 520 90120 90121 90122 90123
W24 Blanking-Off Plug Made to suit all pipe sizes, blanking-off plugs should be used where a rodding point is required in the waste pipe run and also for blanking off inlets of a W612 Dilution Recovery Trap. With its own tapered sealing surface, it replaces the olive, and is held into the fitting by the nut. Cat. No. Nom. Size gms Vinidex Code
W241 38mm 38 90124
W242 51mm 64 90122
W243 W244 76mm 102mm 109 196 90126 90127
W26 Groove Cutting Tool Vulcathene grooving tools enable a groove, of the exact depth and width, to be cut in the correct location from the end of the pipe where the mechanical olive is then located. Cat. No. Nom. Size gms Vinidex Code
W261 W262 W263 W264 38mm 51mm 76mm 102mm 100 146 368 719 90128 90129 90130 90131
38/51mm
76/102mm
W36 Spanner This moulded polycarbonate spanner is made specifically for use with the Vulcathene Mechanical range and should always be used to tighten the Vulcathene nuts as it will not distort or damage the nuts in the process of achieving a secure joint. Cat. No. Nom. Size gms Vinidex Code
W361 38mm 81 90137
W362 W363 51mm 76mm 110 199 90138 90139
W364 102mm 269 90140
57
Vulcathene – Polyfusion Adaptors
C130 Half Coupler Used to convert 38mm Polyfusion pipe to 38mm Mechanical pipe, the threaded end can be screwed to a W271 1¾" pipe coupler to make a mechanical joint. Cat. No. C130 Nom. Size 38mm A 45mm gms 40 Vinidex Code 90220
P758 BSP Coupler Used to convert 38mm Polyfusion pipe to Mechanical (or Enfusion) pipe, the BSP threaded end can be screwed to W15 or L15 series female couplers. Cat. No. P758 Nom. Size 38mm 51mm A 35mm 41mm B 41mm 41mm gms 36 Vinidex Code 90256 V5758201
200 Hand Tool Used for making socket fusion joints in 38mm, the tool can be heated to the required temperature using a gas torch. (See polyfusion jointing information on Page 51). Vinidex Code 32mm V440050 38mm 90192 51mm 90193
L28 Single Socket Long Sweep Bend Available in sizes from 38mm to 152mm, this fitting has an Enfusion socket at one end and a plain spigot at the other. Cat. No. Nom. Size A B gms Vinidex Code
58
L281 L282 L283 L284 L286 38mm 51mm 76mm 102mm 152mm 70mm 83mm 103mm 125mm 167mm 117mm 117mm 171mm 203mm 247mm 90 170 350 510 2000 90309 90310 90311 90312 90313
Vulcathene PP
L29 Single Socket Short Sweep Bend Available in 38mm and 51mm sizes this fitting has an Enfusion socket at one end and a plain spigot at the other. Cat. No. Nom. Size A B gms Vinidex Code
L291 L292 38mm 51mm 43mm 64mm 75mm 97mm 90 120 90314 90315
L17 Double Socket Long Sweep Bend Available in sizes from 38mm to 152mm, this fitting has an Enfusion socket at both ends. Cat. No. Nom. Size A gms Vinidex Code
L171 L172 L173 L174 L176 38mm 51mm 76mm 102mm 152mm 70mm 83mm 103mm 125mm 198mm 101 170 390 530 1760 90279 90280 90281 90282 90283
L18 Double Socket Short Sweep Bend Available in 38mm and 51mm sizes, this fitting has Enfusion sockets at both ends. Cat. No. Nom. Size A gms Vinidex Code
L181 L182 38mm 51mm 43mm 64mm 115 172 90284 90285
L19 45° Double Socket Slow Bend Five standard sizes cover the 38mm to 152mm range, with an Enfusion socket at each end. Cat. No. Nom. Size A gms Vinidex Code
L191 L192 L193 L194 L196 38mm 51mm 76mm 102mm 152mm 19mm 38mm 51mm 51mm 43mm 80 120 300 520 1500 90286 90287 90288 90289 90290
59
Vulcathene PP
L21 45° Single Socket Slow Bend Available in five sizes to suit standard 38mm to 152mm pipe the fitting has an Enfusion socket at one end and a plain spigot at the other end. Cat. No. Nom. Size A B gms Vinidex Code
L211 L212 L213 L214 L216 38mm 51mm 76mm 102mm 152mm 19mm 38mm 51mm 51mm 43mm 38mm 76mm 95mm 100mm 114mm 80 130 260 450 1450 90299 90300 90301 90302 90303
L20 92½° Equal Sweep Tee An equal three branch fitting, the sweep tee is available in four sizes from 38mm to 102mm and has an Enfusion socket on each branch. Cat. No. Nom. Size A B C D gms Vinidex Code
L201 38mm 57mm 70mm 51mm 121mm 103 90291
L202 L203 L204 51mm 76mm 102mm 59mm 79mm 98mm 59mm 78mm 98mm 35mm 46mm 57mm 94mm 124mm 156mm 220 560 1300 90292 90294 90297
L20 92½° Reducing Sweep Tee The range of five fittings covers all reducing branch requirements and have an Enfusion socket on each of the three branches. When ordering, the first two dimensions on the chart below relate to the straight through bore, and the third to the branch diameter. Cat. No. L2021 L2031 L2032 L2042 Nom. Size 51x51x38mm 76x76x38mm 76x76x51mm 102x102x51mm A 57mm 114mm 83mm 100mm B 70mm 90mm 83mm 52mm C 51mm 65mm 70mm 28mm D 121mm 152mm 152mm 81mm gms 140 500 510 550 Vinidex Code 90293 90295 90296 90298
L37 45° Single Wye Covering the sizes from 38mm to 152mm all branches have an Enfusion socket. Cat. No. Nom. Size A B C gms Vinidex Code
60
L371 38mm 83mm 29mm 83mm 200 90325
L372 L373 L374 L376 51mm 76mm 102mm 152mm 92mm 127mm 212mm 214mm 36mm 41mm 46mm 44mm 92mm 127mm 187mm 214mm 240 550 1100 3630 90326 90327 90330 90333
Vulcathene PP
L37 45° Reducing Wye A range of 8 fittings covering most requirements. For ordering the first two dimensions shown on the chart below relate to the straight through bore and the third the branch diameter. All branches have an Enfusion socket. Cat. No. Nom. Size A B C gms Vinidex Code
L3721 51x51x38mm 84mm 27mm 87mm 170 V6037211
Cat. No. L3762 Nom. Size 152x152x51mm A 214mm B 44mm C 262mm gms 2350 Vinidex Code 90334
L3731 L3732 L3742 L3743 76x76x38mm 76x76x51mm 102x102x51mm 102x102x76mm 144mm 144mm 165mm 211mm 22mm 22mm 10mm 46mm 178mm 146mm 165mm 235mm 700 520 814 1500 90328 90329 90331 90332
L3763 L3764 152x152x76mm 152x152x102mm 214mm 214mm 44mm 44mm 262mm 214mm 2360 2360 90335 90336
L35 92½° Double Branch An equal four branch fitting, the double branch is available in three sizes from 51mm to 102mm and has an Enfusion socket on each branch. Cat. No. Nom. Size A B C D gms Vinidex Code
L352 51mm 58mm 59mm 35mm 93mm 370 90316
L353 L354 76mm 102mm 78mm 98mm 79mm 98mm 46mm 57mm 124mm 156mm 650 900 90317 90318
LT1 ‘P’ Trap Available in 76, 102 and 152mm sizes, supplied as three loose components. Cat. No. LT13 LT14 LT16 Nom. Size 76mm 102mm 152mm A 376mm 360mm 651mm B 290mm 445mm 533mm C 160mm 195mm 292mm gms 1200 1700 7200 Vinidex Code 90265 90266 90267
L101 U Bend Available in 38mm and 51mm sizes, this fitting has Enfusion sockets at both ends. A ‘P’ trap configuration can be made by adding an L28 single socket sweep bend. Cat. No. Nom. Size A B gms Vinidex Code
L1011 L1012 38mm 51mm 57mm 87mm 82mm 125mm 150 200 90268 90269
61
Vulcathene PP B
L16 Coupling A
Produced to fit the five sizes of the Enfusion chemical waste drainage system, from 38mm to 152mm, the coupling has an internal stop which forms a smooth through-bore and ensures that the correct depth of pipe is inserted into the fitting. Cat. No. Nom. Size A B gms Vinidex Code
L161 38mm 6mm 61mm 50 90274
L162 51mm 8mm 74mm 80 90275
B
L163 L164 L166 76mm 102mm 152mm 11mm 11mm 13mm 102mm 127mm 183mm 300 510 640 90276 90277 90278
A
L16 (S) Slip Coupling Enfusion slip couplers in sizes 102mm and 152mm can be used where a new branch connection to an existing Vulcathene stack is required. Cat. No. Nom. Size B gms Vinidex Code
L164(S) L166(S) 102mm 152mm 150mm 150mm 646 930 90354 V6416601
B
B
B
L39 Reducing Coupler This range covers the requirement for changing from one pipe size to another. Designed with an Enfusion socket on one end and the other spigot end is fused into a larger Enfusion socket. Cat. No. Nom. Size A gms Vinidex Code
L3912 L3923 L3924 51x38mm 76x51mm 102x51mm 32mm 43mm 51mm 44 160 239 90337 90338 90339
Cat. No. L3934 L3946 Nom. Size 102x76mm 152x102mm A 47mm 64mm gms 214 620 Vinidex Code 90340 90341
Note:
76mm x 38mm reducer: 102mm x 38mm reducer: 152mm x 38mm reducer: 152mm x 51mm reducer: 152mm x 76mm reducer:
Use L3923 reducer + L3912 reducer Use L3924 reducer + L3912 reducer Use L3946 reducer + L3924 reducer + L3912 reducer Use L3946 reducer + L3924 reducer Use L3946 reducer + L3934 reducer
L14 M.I to Pipe Coupler In two sizes, 38mm and 51mm, this fitting has an Enfusion socket on one end and a male thread the other. Cat. No. Nom. Size A gms Vinidex Code
62
L141 L142 38mm 51mm 6mm 6mm 30 60 90270 90271
B
Vulcathene PP
L15 F.I to Pipe Coupler In two sizes, 38mm and 51mm, this fitting has an Enfusion socket on one end and a female thread the other. Cat. No. Nom. Size A gms Vinidex Code
L151 L152 38mm 51mm 8mm 8mm 70 100 90272 90273
L45 Glass Adaptor Produced in flame retardant PP in four sizes from 38mm to 102mm, the fitting has an Enfusion socket on one end and a beaded spigot on the other for connection to nominal glass pipe dimensions DN40, DN50, DN80 & DN100. Cat. No. L451 L452 L453 L454 Nom. Size 38mm 51mm 76mm 102mm A 28mm 32mm 41mm 36mm gms 40 66 400 665 Vinidex Code 90342 90344 90345 V6045404
L801 Thermal Stress Relief Unit Designed for use with 38mm diameter pipe, the L801 can be installed in either vertical or horizontal pipework. When installed it is important to ensure that the end with the moulded fixing clip is the outflow end of the fitting. When installing a stress relief unit, the tail end pipe should be pushed fully ‘home’ and its position marked. It should then be withdrawn 38mm. Cat. No. Nom. Size A min A max Vinidex Code
L801 38mm 70mm 108mm 90346
L802 Thermal Stress Relief Unit Designed for use with 51mm diameter pipe, the L802 can be installed in either vertical or horizontal pipework. When installed it is important to ensure that the end which forms the collar is the outflow end of the fitting. The unit must be anchored with a metal clamp which should be located round the body of the stress relief unit, just below the ridge round the top of the collar. This allows the pipe inserted into the collar to expand and contract. Cat. No. L802 Nom. Size 51mm A min 149mm A max 203mm B 73mm gms 750 Vinidex Code 90347
63
Vulcathene PP
L36 Flange To fit pipe sizes from 38mm to 152mm, the flange is supplied (Table D) drilled or undrilled. Flanges should be clamped together with a nitrile gasket and 4 M20 bolts. Cat. No. L361 Nom. Size 38mm A 98mm B 127mm C 16mm D 14mm gms 280 Vinidex Code (Drilled) 90319 Vinidex Code (Undrilled) V6040101
L362 L363 L364 L366 51mm 76mm 102mm 152mm 114mm 146mm 178mm 235mm 150mm 189mm 228mm 278mm 18mm 23mm 28mm 25mm 17mm 17mm 17mm 17mm 310 600 780 1768 90320 90321 90323 90324 V6040201 V6040301 V6040401 V6040601
L24 Cleanout Plug A simple method for draining or rodding a blocked section, the Cleanout is available to suit pipe sizes from 38mm to 102mm. The fitting comprises of a spigot which can be fused into an Enfusion socket and a threaded plug. The A dimension shows the disassemble length with a clearance allowance of 13mm. Wrap PTFE tape around the thread of the plug to make a seal. Cat. No. Nom. Size A gms Vinidex Code
L241 L242 38mm 51mm 160mm 185mm 140 150 90304 90305
L243 L244 76mm 102mm 185mm 210mm 280 480 90306 90307
Note: For 152mm cleanout, use an L3946 reducer with an L244 cleanout plug.
L2610 Link Cable
L261 Clamp
Link cable leads in 5’ lengths for multiple jointing.
Available in six sizes for 38mm to 152mm fittings, these stainless steel clamps should be fitted over the hubs of the Enfusion sockets and tightened before electrofusion welding.
Vinidex Code
90079
Vinidex Code Sizes: 38mm 90349 51mm 90350 76mm 90351 102mm 90352 152mm 90353
L2601 Enfusion Hand-held Unit
Pipe Scraper
(See specification details on page 44)
Pipe should be thoroughly scraped over an area equal to socket depth plus 50% using a pipe scraper. Replacement blades (2 per packet) are supplied separately.
Vinidex Code
90355
Vinidex Code 90080 Pipe Scraper C53M5002 Replacement Blades
64
Vulcathene PP
Water Service Controls Bench Mounted VX Code
90380 H=240mm S=130mm Swivel swan-neck with serrated nozzle outlet (Anti-rotation pin) Fixed swan-neck is also available: 90378 - left hand control 90379 - right hand control
gms 730
90382 Bib tap with serrated nozzle outlet (Anti-rotation pin)
gms 850
90436 Two way bib tap with serrated nozzle outlet (Anti-rotation pin)
90383 Three way bib tap with serrated nozzle outlet (Anti-rotation pin)
gms 2470
90381 Mixer tap with swivel swan-neck and aerator
gms 1320
90375 Mixer tap with swivel swan-neck on 178mm centres with aerator
gms 1530
65
Vulcathene PP
Water Service Controls Bench Mounted cont. VX Code
90442 Mixer tap with swivel swan-neck and wrist action handles on 178mm centres with aerator
gms 2001
90386 Monobloc single handle mixer with swivel swan-neck with aerator
gms 1590
Water Service Controls Wall/Pendant Mounted 90408 In line tap with serrated nozzle outlet
gms 440
90377 Bib tap with serrated nozzle outlet
gms 420
90435 Mixer swan-neck, 178mm adjustable centres with aerator
gms 1410
VG800416 Two way in line taps with serrated nozzle outlet
gms 920
66
Vulcathene PP
VX Code
90443 Two way angle tap at 180° with serrated nozzle outlet
gms 1220
Treated Water Service Controls VG800298 Angle tap with removable nozzle, ½" outlet, inlet ¼" BSP and 500mm 8 x 1 PP tube gms 180
90385 Bib tap with removable nozzle, ½" outlet, inlet ¼" BSP and 500mm 8 x 1 PP tube
gms 570
Drop Lever Gas Taps Bench/Wall Mounted 90369 One way drop lever gas tap (Anti-rotation pin)
gms 300
90371 Two way, 90° drop lever gas tap (Anti-rotation pin) Two way, 180° drop lever gas tap also available 90370
gms 420
90372 Four way drop lever gas tap (Anti-rotation pin)
gms 700
67
Vulcathene PP
Water Service Controls Bench Mounted cont. VX Code
90373 One way wall mounted drop lever gas tap (Anti-rotation pin)
gms 260
90374 Two way wall mounted drop lever gas tap (Anti-rotation pin)
gms 390
90368 One way wall mounted (replacement) drop lever gas tap
3/8" BSP (m)
50
gms 250
Dry Service Controls Bench Mounted 90387/395/398/401/405 Single valve with fixed serrated nozzle outlet 90387/vacuum 90395/compressed air 90398/nitrogen 90401/natural gas 90405/other pressure gases (please specify) gms 750
90388/396/399/402/406 Two way valve at 180° with fixed serrated nozzle outlets 90388/vacuum 90396/compressed air 90399/nitrogen 90402/natural gas 90406/other pressure gases (please specify) gms 1020
90389/397/400/403/407 Two way valve at 90° with fixed serrated nozzle outlets 90389/vacuum 90397/compressed air 90400/nitrogen 90403/natural gas 90407/other pressure gases (please specify) gms 1000
68
Vulcathene PP
Dry Service Controls Wall/Pendant Mounted VX Code
90409/VG800851/90410/412/414 In line tap with fixed serrated nozzle outlet 90409/vacuum VG800851/compressed air 90410/nitrogen 90412/natural gas 90414/other pressure gases (please specify) gms 460
VG800843/VX800853/90411/413/415 Two way in line tap with fixed serrated nozzle outlets VG800843/vacuum VX800853/compressed air 90411/nitrogen 90413/natural gas 90415/other pressure gases (please specify) gms 790
90390/452/462/472/482 Two way in line tap with fixed nozzle outlets 90390/vacuum 90391/compressed air 90392/nitrogen 90393/natural gas 90394/other pressure gases (please specify) gms 970
90388/396/399/402/406 Two way angle tap at 180° with fixed serrated nozzle outlets 90388/vacuum 90396/compressed air 90399/nitrogen 90402/natural gas 90406/other pressure gases (please specify) gms 1210
90409/VG800851/410/412/414 In line tap with fixed serrated nozzle outlet 90409/vacuum VG800851/compressed air 90410/nitrogen 90412/natural gas 90414/other pressure gases (please specify) gms 460
69
Vulcathene PP
Remote Control Valves and Outlets VX Code
90437/VG801704/705/702/90438/439 Front control valve, inlet and outlet copper tube 10 x 1 90437/cold water VG801704/vacuum VG801705/compressed air VG801702/nitrogen 90438/natural gas 90439/other pressure gases (please specify) gms 520
90404 Fixed swan-neck with fixed serrated nozzle outlet
gms 790
90416/417/418/419/420/421 Bench or wall outlet with fixed serrated nozzle outlet 90416/cold water 90417/vacuum 90418/compressed air 90419/nitrogen 90420/natural gas 90421/other pressure gases (please specify) gms 300
VG800706 Wall outlet with fixed serrated nozzle outlet
gms 330
90422/423/424/425/426/427 Wall outlet with fixed serrated nozzle outlet 90422/cold water 90423/vacuum 90424/compressed air 90425/nitrogen 90426/natural gas 90427/other pressure gases (please specify) gms 250
90428/429/430/431/432/433 Angle wall outlet with fixed serrated nozzle outlet 90428/cold water 90429/vacuum 90430/compressed air 90431/nitrogen 90432/natural gas 90433/other pressure gases (please specify) gms 300
70
Vulcathene PP
Accessories and Parts VX Code
90434
90453
Blind flange
Standard water headwork
90454
VG950153
Plastic headwork for treated waters
Valve for dry services
Handwheel Handwheel 90458/cold water VG960206/treated water VG960201/vacuum VG960202/compressed air VG960203/nitrogen VG960204/natural gas VG960205/other gases (please specify)
90451/452
90449/VG821081
Flange 90451 for 3/8" 90452 for ½"
Nut/Washer 90449 for 3/8" VG821081 for ½"
90456/457 Anti-rotation nut 90456 for 3/8" 90457 for ½"
A
A 42
R2 R. M5
R. 1/2" R. 3/8"
R. M5
71
Vulcathene PP
Associated Laboratory Products VX Code
90461 Emergency Shower/Eye Wash
90459 Emergency Eye Wash
90460 Movable Laboratory Emergency Spray
72
Vulcathene PP
73
Thermoplastic Valves Vinidex offers one of the most comprehensive ranges of high quality, high performance thermoplastic valves and actuation products available today. With more than 65 years of design and manufacturing experience, FIP lightweight, long life, maintenance free valves will save you time and money.
74
Material options such as PVC, CPVC, PP, PVDF, and ABS make our corrosion resistant valves ideal for use in a wide variety of applications. Quarter turn pneumatic and electric actuation, pneumatically actuated diaphragm valves, and many options and accessories allow for fully automated control. Whether a valve is required for isolation, diversion, control, or throttling, Vinidex has a solution to meet your needs.
Applications include:
We offer both manual and actuated thermoplastic valves.
• Chlorine injection, chlorine dioxide and chloralkali plant piping
• Acid products handling for refineries, metal works, etc. • Alum and ferric chloride handling • Aquariums and aquatic animal life support systems • Bleach, dye and acid lines • Brine and seawater systems
• Pharmaceutical • Plant chemical distribution lines • Plant water supply and distribution • Swimming pools • Wash water recovery systems • Water and wastewater treatment
Ball Valves
Butterfly Valves
On/Off Service
3
3
High Capacity
3
3
Throttling
3
3
3
Quick & Frequent Cycling
3 3
3
WHAT TYPE OF VALVE TO USE
Slurries/Dirty Fluids
Diaphragm Valves
Check & Vent Valves
Filtering Back Flow Prevention
3
Air & Gas Release
3
Electro-Mechanical Control Actuation
3
3
3
75
Thermoplastic Valves
VKD Series Ball Valves End Conn.
Size inches
EPDM FPM Vinidex Code Vinidex Code
PVC w/ PTFE Seats Socket Socket Socket Socket Socket Socket Socket Socket
½ ¾ 1 1¼ 1½ 2 3 4
87188 87190 87192 87194 87196 87198 87200 87202
87189 87191 87193 87195 87197 87199 87201 87203
Corzan® CPVC w/ PTFE Seats Socket Socket Socket Socket Socket Socket Socket Socket
½ ¾ 1 1¼ 1½ 2 3 4
87204 87206 87208 87210 87212 87214 87216 87218
87205 87207 87209 87211 87213 87215 87217 87219
PP w/ PTFE Seats
76
Socket Socket Socket Socket Socket
20mm 25mm 32mm 40mm 50mm
87222 87224 87226 87228 87230
87223 87225 87227 87229 87231
Socket
63mm
87232
87233
Thermoplastic Valves
Easyfit VXE Series Ball Valves End Conn.
Size inches
EPDM FPM Vinidex Code Vinidex Code
PVC, w/ PTFE Seats (Socket) Socket
½
87264
-
Socket
¾
87265
-
Socket
1
87266
-
Socket
1¼
87267
-
Socket
1½
87268
-
Socket
2
87269
-
Socket
3
87270
87271
Socket
4
87272
87273
PVC, w/ PTFE Seats (Threaded) Threaded
½
87274
87275 87277
Threaded
¾
87276
Threaded
1
87278
87279
Threaded
1¼
87280
87281
Threaded
1½
87282
87283
Threaded
2
87284
87285
CPVC, w/ PTFE Seats (Socket) Socket
½
87286
87287
Socket
¾
87288
87289
Socket
1
87290
87291
Socket
1¼
87292
87293
Socket
1½
87294
87295
Socket
2
87296
87297
Socket
3
87298
87299
Socket
4
87300
87301
77
Thermoplastic Valves
Easyfit VEE Series Ball Valves End Conn.
Size inches
EPDM Vinidex Code
PVC c/w PTFE Seats (Socket) Socket
½
87302
Socket
¾
87303
Socket
1
87304
Socket
1¼
87305
Socket
1½
87306
Socket
2
87307
Socket
3
87308
Socket
4
87309
PVC c/w PTFE Seats (Threaded) Threaded
½
87310
Threaded
¾
87311
Threaded
1
87312
Threaded
1¼
87313
Threaded
1½
87314
Threaded
2
87315
Threaded
3
87316
Threaded
4
87317
TKD Series 3-way Ball Valves
End Conn.
Size inches
EPDM FPM Vinidex Code Vinidex Code
PVC w/ PTFE Seats, L-Port Socket
½
87240
87241
Socket
¾
87242
87243
Socket
1
87244
87245
Socket
1¼
87246
87247
Socket
1½
87248
87249
Socket
2
87250
87251
PVC w/ PTFE Seats, T-Port
78
Socket
½
87252
87253
Socket
¾
87254
87255
Socket
1
87256
87257
Socket
1¼
87258
87259
Socket
1½
87260
87261
Socket
2
87262
87263
Thermoplastic Valves
FK Series Butterfly Valves Size (mm)
EPDM Vinidex Code
FPM Vinidex Code
50mm
87384
87385
63mm
87386
87387
75mm
87388
87389
90mm
87390
87391
110mm
87392
87393
140mm
87394
87395
160mm
87396
87397
225mm
87398
87399
50mm
87400
87401
63mm
87402
87403
75mm
87404
87405
PVC Wafer Style
CPVC Wafer Style
90mm
87406
87407
110mm
87408
87409
140mm
87410
87411
160mm
87412
87413
225mm
87414
87415
Size (mm)
EPDM Vinidex Code
FPM Vinidex Code
50mm
87416
87417
63mm
87418
87419
75mm
87420
87421
90mm
87422
87423
110mm
87424
87425
140mm
87426
87427
160mm
87428
87429
225mm
87430
87431
FE Series Butterfly Valves
PVC Wafer Style
NBR and FPM lined valves are available upon request.
79
Thermoplastic Valves
SXE Series Ball Check Valves End Connection
Size inches
EPDM Vinidex Code
FPM Vinidex Code
Socket
½
87318
87319
Socket
¾
87320
87321
Socket
1
87322
87323
Socket
1¼
87324
87325
Socket
1½
87326
87327
Socket
2
87328
87329
Socket
3
87330
87331
Socket
4
87332
87333
Socket
½
87334
87335
Socket
¾
87336
87337
Socket
1
87338
87339
Socket
1¼
87340
87341
Socket
1½
87342
87343
Socket
2
87344
87345
Socket
3
87346
87347
Socket
4
87348
87349
PVC
CPVC
SSE Series Spring Assisted Ball Check Valves End Connection
Size inches
EPDM Vinidex Code
PVC (Socket)
80
Socket
½
87350
Socket
¾
87352
Socket
1
87354
Socket
1¼
87356
Socket
1½
87358
Socket
2
87360
Socket
3
87362
Socket
4
87363
Thermoplastic Valves
VRU Series Check Valves End Connection
Size inches
EPDM Vinidex Code
Socket
½
87364
Socket
¾
87365
Socket
1
87366
PVC (Socket)
Socket
1¼
87367
Socket
1½
87368
Socket
2
87369
PVC (Threaded) Threaded
½
87370
Threaded
¾
87371
Threaded
1
87372
Threaded
1¼
87373
Threaded
1½
87374
Threaded
2
87375
Size inches
EPDM Vinidex Code
RV Series Sediment Strainers – True Union – Y Pattern End Connection
Clear PVC True Union, w/PVC 35 Mesh Screen S/T
½
87376
S/T
¾
87377
S/T
1
87378
S/T
1¼
87379
S/T
1½
87380
S/T
2
87381
Clear PVC NOT True Union, w/PVC 35 Mesh Screen Socket
3
87382
Socket
4
87383
DK Series Diaphragm Valves End Connection
Size inches
EPDM Vinidex Code
FPM Vinidex Code
PTFE Vinidex Code
Socket
½
87432
87433
87434
Socket
¾
87435
87436
87437
Socket
1
87438
87439
87440
Socket
1¼
87441
87442
87443
Socket
1½
87444
87445
87446
Socket
2
87447
87448
87449
81
Ultragrip Pioneers in pipe solutions. Next Generation UltraGrip is designed to offer a solution to joining plain-ended pipes and contains an end load resistant mechanism that grips and seals onto a variety of pipe materials including Cast Iron, Ductile Iron, Steel, PVC and PE.
82
The UltraGrip range is available in sizes DN40 – DN600. This gives you a single sealing and gripping product solution to cover the majority of pipes installed in an underground water network. The larger sized UltraGrip has been methodologically engineered to support a progressive gripping mechanism through an enhanced design, which has a larger footprint to increase the area of actuation at the point of contact. This results in an evenly distributed gripping function. It has also been designed to accommodate rough on-site handling through an intelligent carrier that maintains the gasket and grippers within the end ring, ensuring the fitting can be easily slid onto the pipe with no interference. PE Solutions Two solutions for connecting PE and rigid pipes are available. Choose from the UltraGrip range of couplings and adaptors or use the UltraGrip Pecat adaptor. Repair Solutions
In addition, the grippers are removable, allowing UltraGrip to be converted to a flexible product to allow for axial movement. The gripper and seal subassembly can accommodate diameter pipe outside variation up to 54mm, depending on nominal size. Corrosion Protection UltraGrip metal components are coated with Rilsan Nylon 11. Rilsan benefits include long term corrosion protection and resistance to impact damage. Additionally, the nuts and bolts are stainless steel coated with Dacromet/dry film lubricant, which prevents galling and provides long term corrosion protection. Hygienic Protective Caps Protection caps have been introduced to keep the fitting clean and free from any contamination. The caps are made of recyclable material to minimize the impact to the environment and ensure fittings rae clean and ready for use on potable water (DN600) or gas (DN400) applications.
UltraGrip offers the ideal solution for repairing severely damaged, corroded or completely shattered pipes in difficult trench conditions. Progressive Gripping One of the key components of UltraGrip is the progressive gripping mechanism, which enhances its end-load restraint capabilities as the internal pressure in the pipe increases. A unique gripper system is suitable for all recommended pipe materials and combined with an engineered intelligent carrier which ensures maximum gripping strength around the full pipe circumference. This is achieved through uniform movement during installation and bolt-up.
83
Ultragrip – Coupler
Size Range
Insertion Depth (D)
Nom Size
Min
Max
Min
57392
40
43.5
63.5
65
57393
50
48.0
71.0
65
57394
65
63.0
83.7
65
57395
80
85.7
107.0
65
57396
100
107.0
133.2
90
57397
125
132.2
160.2
90
57398
150
158.2
192.2
57399
175
192.2
57400
200
218.1
VX Code
Max
Dimensions Overall
Bolts
Sleeve
No-size
A
B
L
T
95
168
262
144
7.0
6-M12x70
110
178
296
180
5.0
6-M12x70
95
189
262
144
7.0
6-M12x70
110
212
288
170
7.0
6-M12x70
125
280
342
180
7.0
6-M16x93
125
305
342
180
6.0
6-M16x93
90
135
339
386
213
6.5
8-M16x93
226.9
125
165
403
400
220
6.5
10-M16x93
256.0
125
165
432
400
220
6.5
10-M16x93
57401
250
266.2
310.0
125
165
476
524
300
8.0
12-M16x120
57402
300
315.0
356.0
125
200
522
524
300
8.0
16-M16x120
57403
350
352.2
396.0
125
200
577
525
300
7.5
18-M16x120
57404
400
398.2
442.0
125
200
623
525
300
7.5
20-M16x120
57405
450
448.0
492.0
135
215
713
545
300
7.5
24-M16 x 150
57406
500
498.0
552.0
155
215
803
565
300
7.5
18-M20 x 150
57407
500
558.0
608.0
155
215
860
565
300
7.5
20-M20 x 150
57408
600
604.0
648.0
155
215
900
565
300
7.5
24-M20 x 150
57409
600
676.0
726.0
155
215
975
565
300
7.5
28-M20 x 150
Working Pressure & Temperature Ratings Gripping Product
Nominal Size
Gas
Water
Gas
Water
DN40 to DN300
5bar
16bar
5bar
16bar
DN350 to DN400
5bar
10bar
5bar
10bar
DN450 to DN600
N/A
10bar
N/A
10bar
B
Notes: 1) Site Test Pressure – 1.5 times working pressure.
D L
T
84
Flex Product
A
2)
Factory Test Pressure – The minimum requirement in European Standards is 1.5 times working pressure plus 5bar (e.g. 29bar for 16bar working pressure), but in many cases Viking Johnson reaches substantially higher levels – up to 36bar.
3) All water contact components are approved for use with Potable Water.
Operating Temperature
-20°C to +30°C
Ultragrip – Support Liner for PE & PVC Pipes
Support Liner - Standard - 1mm thickness VX Code
Pipe OD*
Insert length L (mm)
SDR Rating
Wedge Length W (mm)
57495
63
130
SDR 11
220
57414
75
130
SDR 11
220
57417
90
130
SDR 17
220
-
90
130
SDR 13, 6
220
57416
90
130
SDR 11
220
57419
110
150
SDR 17
220
-
110
150
SDR 13, 6
220
57418
110
150
SDR 11
220
57421
125
150
SDR 17
220
57420
125
150
SDR 11
220
57422
140
150
SDR 11
220
57425
160
175
SDR 17
220
-
160
175
SDR 13, 6
220
57424
160
175
SDR 11
220
57427
180
175
SDR 17
220
57426
180
175
SDR 11
220
Note: DN40 and DN 50 are available on request.
Support Liner - Standard - 2mm thickness 57429
200
180
SDR 17
220
57428
200
180
SDR 11
220
57431
225
180
SDR 17
220
57430
225
180
SDR 11
220
57432
250
180
SDR 11
220
57435
280
200
SDR 17
220
-
280
200
SDR 13, 6
220
57434
280
200
SDR 11
220
57437
315
200
SDR 17
220
57436
315
200
SDR 11
220
57439
355
200
SDR 17
220
57438
355
200
SDR 11
220
57440
400
200
SDR 11
220
57441
400
200
SDR 17
220
Support Liner - Standard - 3mm thickness 57422
450
240
SDR 11
300
57443
450
240
SDR 17
300
57444
500
240
SDR 11
300
57445
500
240
SDR 17
300
57446
560
240
SDR 11
300
57447
560
240
SDR 17
300
57448
630
240
SDR 11
300
57449
630
240
SDR 17
300
57450
710
240
SDR 11
300
57451
710
240
SDR 17
300
85
Straub The name STRAUB is synonymous with expertise, quality and reliability. As an internationally renowned manufacturer of pipe joints, STRAUB not only invented ”the original”, it also owns the patents on several outstanding features that still make the famous STRAUB pipe coupling the unquestioned leader in its class. Our unique pipe coupling concept is backed by 40 years of experience and continuous development, guaranteeing Swiss quality and value.
86
Our total product and customer focus enables us to respond quickly and efficiently to our customers’ most stringent requirements. There is no substitute for our experience. STRAUB invented the “original” and continues to refine and improve the design today. Pipe couplings are our only business – we are passionate about what we do.
The progressive sealing effect As the pressure in the pipe increases, so does the force on the sealing lips, due to the flow through the pressure equalisation channel. The progressive anchoring effect
We obtained the ISO 9001 Quality Assurance Certificate in 1995 and ISO 14001 in 2008. This confirms proven STRAUB quality and made us once again world pioneers in the area of progressive sealing pipe joints.
As the axial loading on the pipe increases due to increased internal pressure or external influences, the teeth bite even deeper into the pipe to compensate. The penetration depth of the anchoring ring teeth under pressure is 0.1 – 0.3 mm.
One unique technical principle: two basic types, but with innumerable applications, wherever pipes have to be joined together - that is the secret of STRAUB pipe joints. Based on the well-proven coupling technology, we combine different pipe materials for optimum solutions for customers.
STRAUB-METAL-GRIP is a high-performance coupling suitable for all pipe systems. This coupling is mainly used for building construction or civil engineering, power plants and demanding shipbuilding / offshore applications or as a machinery component.
Their safety and reliability have been examined and certificated by public authorities, insurance companies, technical inspectorates and licensing institutions for all the major industrial sectors in most industrial countries. You can rely on STRAUB couplings.
STRAUB-METAL-GRIP also absorbs unexpected field stress and applies perfect for seismic retrofits.
87
Straub
STRAUB-METAL-GRIP Ø 30.0 - 219.1 mm
VX Code VX Code NBR NBR 75970 75971 75972 75973 75974 75975 75976 75977 75978 75979 75980 75981 75982 75983 75984 75985 75986 75987 75988 75989 75990 75991 75992
75993 75994 75995 75996 75997 75998 75999 76000 76001 76002 76003 76004 76005 76006 76007 76008 76009 76010 76011 76012 76013 76014
Sealing Sleeve
Temp:
-30º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +125º C
H-NBR (on request)
Medium:
water, gas, oil and fuel and other hydrocarbons
Pipe OD (mm)
Clamping Range (mm)
PS (bar)
B (mm)
C (mm)
DV (mm)
KV (mm)
Pipe Gap with Strip Insert (mm)
Torque rate (Nm)
Allen head (mm)
30.0 33.7 38.0 42.4 44.5 48.3 54.0 57.0 60.3 63.5 76.1 84.0 88.9 104.0 108.0 114.3 129.0 133.0 139.7 154.0 159.0 168.3 219.1
29.5 - 30.5 33.2 - 34.2 37.5 - 38.5 41.9 - 42.9 44.0 - 45.0 47.8 - 48.8 53.5 - 54.5 56.4 - 57.6 59.7 - 60.9 62.9 - 64.1 75.3 - 76.9 83.2 - 84.8 88.0 - 89.8 103.0 - 105.0 106.9 - 109.1 113.2 - 115.4 127.7 - 130.3 131.7 - 134.3 138.3 - 141.1 152.5 - 155.5 157.4 - 160.6 166.6 - 170.0 216.9 - 221.3
67.0 62.0 58.0 53.0 48.0 44.0 39.0 37.0 37.0 37.0 56.0 45.0 41.0 37.0 35.0 34.0 33.0 33.0 32.0 32.0 31.0 29.0 26.0
46/67 46/67 61.0 61 61 61 77 77 77 77 94 94 94 94 94 94 108 108 109 109 109 109 150
18 18 19 20 20 20 38 32 32 32 39 39 39 39 39 39 43 43 43 51 43 43 60
47 52 58 62 64 68 74 77 82 84 100 112 117 133 133 139 160 160 168 186 187 200 259
70 75 90 90 95 95 100 105 110 114 130 140 145 160 160 165 190 190 200 215 215 230 295
5 5 5-10 5-10 5-10 5-10 5-15 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-35
10 10 15 15 15 15 20 20 20 35 35 35 35 35 35 35 60 60 60 60 60 60 100
8 8 8 8 8 8 8 8 8 8 10 10 10 10 10 10 12 12 12 12 12 12 16
Available upon request Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Material Grade W4 304 Stainless Steel Test pressure = PS x 1.5 (for example industry, water supply etc.) The pressure values are valid on radial rigid carbon steel pipes under static loads Refer to the technical manual for minimum wall thickness of pipe Strip inserts are supplied with all couplings sold in Australia
88
Straub
STRAUB-METAL-GRIP Ø 180.0 - 609.6 mm
OD [mm]
Clamping range [mm]
180.0 193.7 200.0 206.0 244.5 267.0 273.0 323.9 355.6 406.4 457.2 508.0 558.8 609.6
178.0 - 182.0 192.0 - 195.5 198.0 - 202.0 204.0 - 208.0 242.0 - 247.0 264.5 - 269.5 270.5 - 275.5 320.5 - 327.0 352.0 - 359.0 402.5 - 410.5 452.5 - 462.0 503.0 - 513.0 554.0 - 564.0 604.5 - 614.5
PS [bar]
B [mm]
C [mm]
Sealing Sleeve
Temp:
-30º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
DV [mm]
29.0 148 67 29.0 148 67 28.0 148 67 28.0 148 67 27.0 148 67 24.0 148 67 21.0 148 67 18.0 148 67 17.0 148 67 14.0 148 67 8.0 148 67 6.0 148 67 6.0 148 67 5.0 148 67 STRAUB produces custom
KV [mm]
R without strip insert [mm]
R with strip insert [mm]
225 285 5-15 5-35 239 300 5-15 5-35 245 305 5-15 5-35 251 310 5-15 5-35 290 345 5-15 5-35 312 365 5-15 5-35 318 370 5-15 5-35 369 420 5-15 5-35 401 450 5-15 5-35 451 500 5-15 5-35 502 550 5-15 5-35 604 600 5-15 5-35 604 650 5-15 5-35 655 700 5-15 5-35 made couplings from 180.0 up to 609.6 mm
Torque rate [Nm]
Allen head [mm]
Thread M...
150 150 180 180 180 180 180 230 230 230 250 250 300 300
17 17 17 17 17 17 17 17 17 17 17 17 17 17
20 20 20 20 20 20 20 20 20 20 20 20 20 20
Remarks: METAL GRIP 180.9 - 609.6 are available upon request. Follow fitting / disassembly instructions PS = Working pressure considering the application loads Material Grade W1 Hot Dipped Galvanized Test pressure = PS x 1.5 (for example industry, water supply etc.) The pressure values are valid on radial rigid carbon steel pipes under static loads
89
Straub
STRAUB-GRIP-L Ø 21.3 - 219.1 mm
26.9 - 60.3 with single bolt Sealing Sleeve
Temp:
-30º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +125º C
H-NBR (on request)
Medium:
water, gas, oil and fuel and other hydrocarbons
VX Code VX Code NBR NBR 76041 76042 76043 76044 76045 76046 76047 76048 76049 76050 76051 76052 76053 76054 76055 76056 76057 76058 76059 76060 76061 76062 76063 76064 76065 76066 76067 76068 76069 76070 76071 76072 76073 76074 76075 76080
76098 76099 76100 76101 76102 76103 76104 76105 76106 76107 76108 76109 76110 76111 76112 76113 76114 76115 76116 76117 76118 76119 76120 76121 76122 76123 76124 76125 76126 76127 76128 76129 76130 76135
Pipe OD (mm)
Clamping Range (mm)
PS (bar)
B (mm)
C (mm)
DV (mm)
KV (mm)
Pipe Gap with Strip Insert (mm)
Torque rate (Nm)
Allen head (mm)
21.3 26.9 30.0 33.7 38.0 42.4 44.5 48.3 50.8 54.0 57.0 60.3 63.5 66.6 70.0 73.0 76.1 79.5 84.0 88.9 100.6 101.6 104.0 104.8 108.0 114.3 127.0 129.0 130.2 133.0 139.7 141.3 154.0 159.0 168.3 219.1
20.8 - 21.8 26.4 - 27.4 29.5 - 30.5 33.2 - 34.2 37.5 - 38.5 41.9 - 42.9 44.0 - 45.0 47.8 - 48.8 50.2 - 51.4 53.5 - 54.5 56.4 - 57.6 59.7 - 60.9 62.9 - 64.1 64.9 - 67.3 68.9 - 70.7 72.3 - 73.7 75.3 - 76.9 78.7 - 80.3 83.2 - 84.8 88.0 - 89.8 99.6 - 101.6 100.6 - 102.6 103.0 - 105.0 103.8 - 105.8 106.9 - 109.1 113.2 - 115.4 125.7 - 128.3 127.7 - 130.3 128.9 - 131.5 131.7 - 134.3 138.3 - 141.1 139.9 - 142.7 152.5 - 155.5 157.4 - 160.6 166.6 - 170.0 216.9 - 221.3
36.0 46.0 42.0 38.0 33.0 30.0 33.0 30.0 20.0 20.0 18.0 22.0 37.0 34.0 32.0 31.0 31.0 28.0 26.0 22.0 22.0 22.0 22.0 22.0 21.0 16.0 19.0 19.0 19.0 19.0 16.0 16.0 16.0 16.0 16.0 16.0
45 46 46 46 61 61 61 61 76 76 76 76 77 95 95 95 95 95 95 95 95 95 95 95 95 95 110 110 110 110 110 110 110 110 110 142
18 19 17 17 25 25 25 25 36 37 37 37 32 35 36 41 41 35 35 41 35 35 35 35 41 41 54 54 54 54 54 54 54 54 54 80
43 43 47 51 57 62 64 67 76 76 76 79 84 87 92 96 98 100 112 111 129 130 132 133 130 136 151 153 154 157 164 166 184 183 192 250
70 70 75 75 90 95 95 100 105 105 105 110 114 126 131 142 142 142 152 157 172 172 172 172 172 177 195 195 200 200 210 210 225 225 230 295
5 5 5 5 5-10 5-10 5-10 5-10 5-10 5-15 5-15 5-15 5-25 5-20 5-20 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-25 5-30 5-30 5-30 5-30 5-30 5-30 5-30 5-30 5-30 5-30
10 5 5 5 7.5 7.5 7.5 7.5 7.5 7.5 10 7.5 35 10 10 12 12 12 12 12 12 15 12 12 12 12 20 20 20 20 20 20 20 20 20 60
9 5 5 5 6 6 6 6 6 6 6 6 8 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8 8 10
Available upon request Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Material Grade W5 316 Stainless Steel Test pressure = PS x 1.5 (for example industry, water supply etc.) The pressure values are valid on radial rigid carbon steel pipes under static loads Refer to the technical manual for minimum wall thickness of pipe Strip inserts are supplied with all couplings sold in Australia
90
Straub
STRAUB-GRIP-L Ø 180.0 - 711.2 mm
VX Code VX Code NBR NBR 76076 76077 76078 76079
76131 76132 76133 76134
76081 76082 76083 76084
76136 76137 76138 76139
76085 76086 76087 76088
76140 76141 76142 76143
76089 76090 76091 76092 76093 76094 76095 76096 70697
76144 76145 76146 76147 76148 76149 76150 76151
Sealing Sleeve
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +180º C
FPM / FKM
Medium:
ozone, oxygen, acids, gas, oil & fuel (only with strip insert)
Pipe OD (mm)
Clamping Range (mm)
PS (bar)
B (mm)
C (mm)
DV (mm)
KV (mm)
Pipe Gap with Strip Insert (mm)
Torque rate (Nm)
Allen head (mm)
180.0 193.7 200.0 204.0 206.0 232.0 244.5 250.0 254.0 256.0 267.0 273.0 286.0 304.0 306.0 315.0 323.9 355.6 406.4 457.2 508.0 558.8 609.6 711.2
178.0 - 182.0 192.0 - 195.5 198.0 - 202.0 202.0 - 206.0 204.0 - 208.0 230.0 - 234.0 242.0 - 247.0 247.5 - 252.5 251.5 - 256.5 253.5 - 258.5 264.5 - 269.5 270.5 - 275.5 284.0 - 288.0 301.0 - 307.0 303.0 - 309.0 312.0 - 318.0 320.5 - 327.0 352.0 - 359.0 402.5 - 410.5 452.5 - 461.5 503.5 - 512.5 554.5 - 563.5 605.5 - 614.0 707.1 - 715.6
16.0 16.0 15.0 14.0 14.0 9.0 9.0 9.0 9.0 9.0 8.0 7.0 6.0 6.0 6.0 5.0 5.0 10.0 7.0 5.0 4.0 3.0 2.0 1.0
141 141 141 141 141 141 141 141 141 141 141 141 141 141 141 141 141 141 141 141 141 141 141 141
80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80
205 224 230 234 234 262 275 280 284 284 297 303 316 334 334 345 354 386 436 487 538 589 640 742
255 270 275 280 234 308 320 325 325 325 340 345 355 375 375 386 395 425 470 520 570 620 670 770
5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35 5-35
50 50 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60 60 60 60 60 120
10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 14
Available upon request Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Material Grade W5 316 Stainless Steel Test pressure = PS x 1.5 (for example industry, water supply etc.) The pressure values are valid on radial rigid carbon steel pipes under static loads Refer to the technical manual for minimum wall thickness of pipe Strip inserts are supplied with all couplings sold in Australia
91
Straub
STRAUB-COMBI-GRIP Ø 40.0 - 160.0 mm
VX Code VX Code NBR NBR
76031 76032 76033 76034
76035
Pipe OD (mm)
40.0/38.0 40.0/42.4 50.0/48.3 63.0/60.3 75.0/76.1 76039 90.0/88.9 110.0/108.0 110.0/114.3 76040 114.3/114.3 140.0/139.7 160.0/159.0
76036 76037 76038
Sealing Sleeve
Temp:
-30º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Clamping Range (mm) Plastic | Metal
PS (bar)
B (mm)
C (mm)
DV (mm)
KV (mm)
39.0-40.5 I 37.5-39.0 39.0-40.5 I 42.0-43.5 49.0-50.5 I 47.8-49.0 62.0-64.0 I 59.7-61.0 74.0-76.0 I 75.0-77.5 89.0-91.0 I 87.0-90.0 109.0-111.0 I 106.5-110.5 109.0-111.0 I 112.0-116.0 113.0-115.0 I 112.0-116.0 139.0-142.0 I 137.5-141.0 159.0-162.0 I 157.0-160.5
16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0
61 61 61 76 94 94 94 97 94 109 109
19 20 26 32 39 39 39 45 39 43 43
60 63 70 85 100 118 135 139 140 168 188
90 95 100 115 137 152 167 172 177 200 215
Pipe Gap with Torque rate Strip Insert (mm) (Nm) 5-10 5-10 5-10 5-25 5-25 5-25 5-25 5-25 5-25 5-30 5-30
15 15 15 20 25 25 25 25 25 60 60
Allen head (mm) 6 6 6 6 8 8 8 8 8 10 10
Available upon request
STRAUB-PLAST-GRIP Ø 40.0 - 160.0 mm
VX Code VX Code NBR NBR
76031 76032 76033 76034
76035
Pipe OD (mm)
40.0/38.0 40.0/42.4 50.0/48.3 63.0/60.3 75.0/76.1 76039 90.0/88.9 110.0/108.0 110.0/114.3 76040 114.3/114.3 140.0/139.7 160.0/159.0
76036 76037 76038
Sealing Sleeve
Temp:
-30º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Clamping Range (mm) Plastic | Metal
PS (bar)
B (mm)
C (mm)
DV (mm)
KV (mm)
39.0-40.5 I 37.5-39.0 39.0-40.5 I 42.0-43.5 49.0-50.5 I 47.8-49.0 62.0-64.0 I 59.7-61.0 74.0-76.0 I 75.0-77.5 89.0-91.0 I 87.0-90.0 109.0-111.0 I 106.5-110.5 109.0-111.0 I 112.0-116.0 113.0-115.0 I 112.0-116.0 139.0-142.0 I 137.5-141.0 159.0-162.0 I 157.0-160.5
16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0
61 61 61 76 94 94 94 97 94 109 109
19 20 26 32 39 39 39 45 39 43 43
60 63 70 85 100 118 135 139 140 168 188
90 95 100 115 137 152 167 172 177 200 215
Available upon request Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Material Grade W4 304 Stainless Steel Test pressure = PS x 1.5 (for example industry, water supply etc.) For the installation of pipes made of HDPE and PP, Straub stiffening rings are required Strip inserts are supplied with all couplings sold in Australia
92
Pipe Gap with Torque rate Strip Insert (mm) (Nm) 5-10 5-10 5-10 5-25 5-25 5-25 5-25 5-25 5-25 5-30 5-30
15 15 15 20 25 25 25 25 25 60 60
Allen head (mm) 6 6 6 6 8 8 8 8 8 10 10
Straub
STRAUB-FLEX 1L Ø 48.3 - 168.3 mm
VX Code VX Code NBR NBR 76172 76173 76174 76175 76176 76177 76178 76179 76180 76181 76182 76183 76184 76185 76186 76187 76188 76189 76190 76191 76192 76193 76194
76195 76196 76197 76198 76199 76200 76201 76202 76203 76204 76205 76206 76207 76208 76209 76210 76211 76212 76213 76214 76215 76216 76217
Sealing Sleeve
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +180º C
FPM / FKM
Medium:
ozone, oxygen, acids, gas, oil & fuel (only with strip insert)
Pipe OD (mm)
Clamping Range (mm)
PS (bar)
B (mm)
C (mm)
DV (mm)
KV (mm)
Pipe Gap with Strip Insert (mm)
Torque rate (Nm)
Allen head (mm)
48.3 54.0 57.0 60.3 73.0 76.1 84.0 88.9 100.6 101.6 104.0 104.8 108.0 114.3 127.0 129.0 130.2 133.0 139.7 141.3 154.0 159.0 168.3
47.0 - 49.5 52.5 - 55.5 55.5 - 58.5 59.0 - 61.5 71.5 - 74.5 74.5 - 77.5 82.5 - 85.5 87.5 - 90.5 99.0 - 102.5 100.0 - 103.5 102.5 - 105.5 103.0 - 106.5 106.5 - 109.5 112.5 - 116.0 125.0 - 129.0 127.0 - 131.0 128.5 - 132.0 131.0 - 135.0 138.0 - 141.5 139.5 - 143.0 152.0 - 156.0 157.0 - 161.0 166.0 - 170.5
25.0 25.0 25.0 25.0 25.0 25.0 24.0 24.0 23.0 23.0 22.0 22.0 22.0 21.0 19.0 18.0 18.0 16.0 16.0 16.0 16.0 16.0 16.0
75 75 75 75 94 94 94 94 94 94 94 94 94 94 107 107 107 107 107 107 107 107 107
35 35 35 35 51 51 51 51 51 51 51 51 51 51 62 62 62 62 62 62 62 62 62
70 76 79 82 95 98 106 111 123 124 126 127 130 136 149 151 152 155 162 163 176 181 190
85 90 95 95 117 122 127 132 147 147 147 147 152 157 165 165 165 170 175 180 190 195 205
15 15 15 15 25 25 25 25 25 25 25 25 25 25 35 35 35 35 35 35 35 35 35
8 8 8 8 8 8 8 8 8 8 8 8 8 8 10 10 10 10 10 10 10 10 10
6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8 8
Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Material Grade W5 316 Stainless Steel Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Strip inserts are supplied with all couplings sold in Australia
93
Straub
STRAUB-FLEX 2 Ø 172.0 - 2032.0 mm
Pipe OD (mm)
Clamping Range (mm)
VX Code (LS) EPDM
180.0 200.0 204.0 219.1 232.0 250.0 254.0 267.0 273.0 285.0 304.0 315.0 323.9 335.0 336.0 345.0 355.6 368.0 376.0 386.0 406.4 418.0 424.0 457.2 469.0 470.0 481.0 508.0 521.0 534.0 558.8 560.0 571.0 587.0 609.6 622.0 635.0 648.0 667.0 672.0 711.2 762.0 785.0 812.8 826.0 914.4 924.0 960.0 1016.0 1026.0 1219.2 1229.0
178 - 182 198 - 202 202 - 206 217 - 222 230 - 235 248 - 253 252 - 255 264 - 270 270 - 276 282 - 288 301 - 307 312 - 318 321 - 327 332 - 338 333 - 339 342 - 348 353 - 358 365 - 371 373 - 379 383 - 389 404 - 409 415 - 421 421 - 427 454 - 460 466 - 472 467 - 473 478 - 484 505 - 511 518 - 524 531 - 537 556 - 562 557 - 563 568 - 571 584 - 590 606 - 613 619 - 625 632 - 638 645 - 651 664 - 670 669 - 675 708 - 715 758 - 766 781 - 789 809 - 817 822 - 830 910 - 918 920 - 928 956 - 964 1012 - 1020 1022 - 1030 1215 - 1224 1225 - 1233
76236 76237 76238 76239
VX Code (LS) NBR
76283 76284
76240 76241 76242 76243 76244 76245 76246 76247 76248 76249 76250 76251 76252 76253 76254 76255 76256 76257 76259 76260 76261 76262 76263 76264 76265 76266 76267 76268 76269 76270 76271 76273 76275
76285 76286
76287
76288
76289
76290
76291
76292
76276 76278
76280 76282
Sealing Sleeve
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +180º C
FPM / FKM
Medium:
ozone, oxygen, acids, gas, oil & fuel (only with strip insert)
PS (Bar)
VX Code (LU) EPDM
16.5 15.0 13.5 13.5 12.0 12.0 11.0 11.0 11.0 10.0 10.0 9.5 9.5 9.0 8.5 8.5 8.5 7.5 7.5 7.5 7.5 6.5 6.5 6.5 6.0 6.0 6.0 6.0 5.5 5.5 5.5 5.0 5.0 5.0 5.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 3.5 3.5 3.5 3.5 3.0 3.0 3.0 2.5 2.5 2.5
76297
VX Code (LU) NBR
76298 76299 76300 76301 76302
76335
76304 76305
76336 76337
76306 76307
76308 76310 76311 76313 76314 76315 76317 76318
76339 76340
76341
76342
76319
76320 76321
76322
76324
76325 76326 76328 76329 76330 76333
76344 76345
PS (Bar) 25.0 25.0 25.0 25.0 24.0 24.0 22.5 22.5 22.0 19.5 19.5 18.5 18.5 18.0 17.0 17.0 17.0 15.0 15.0 15.0 15.0 13.0 13.0 13.0 12.0 12.0 12.0 12.0 10.5 10.5 10.5 10.0 10.0 10.0 10.0 8.5 8.5 8.5 8.5 8.5 8.5 8.0 7.5 7.5 7.0 6.5 6.0 6.0 6.0 5.5 5.0 5.0
Torque rate Torque rate (LS) (LU) 15 15 15 15 15 15 15 15 15 15 20 20 20 20 20 20 20 20 20 20 20 20 20 20 25 25 25 25 25 25 25 25 25 25 25 30 30 30 30 30 30 30 30 30 35 35 35 35 35 40 40 40
Available upon request B DV C Rmax.
94
Width of pipe coupling: FLEX 2 L = 138 mm FLEX 2 LS =139 mm FLEX 2 LU = 141 mm FLEX 2 LV = 141 mm FLEX 2 H = 142 mm FLEX 2 XS = 148 mm Outside diameter of the coupling installed = OD+27 mm Distance between sealing lips = 91 mm Distance between pipe ends with strip insert = 35 mm Distance between pipe ends without strip insert = 10 mm
Remarks: Follow fitting / disassembly instructions Available in one or two-piece version PS = Working pressure considering the application loads Material Grade W5 316 Stainless Steel Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Strip inserts are supplied with all couplings sold in Australia
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 60 60 60 60 60 60 60
Straub
STRAUB-FLEX 2 Ø 172.0 - 2032.0 mm
Pipe
Clamping range
OD [mm]
[mm]
172.0 180.0 200.0 219.1 250.0 267.0 273.0 304.0 323.9 355.6 406.4 457.2 508.0 558.8 609.6 711.2 762.0 812.8 914.4 1016.0 1117.6 1219.2 1320.8 1422.4 1524.0 1600.0 1625.6 1727.2 1828.8 1930.4 2032.0
Sealing Sleeve
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +180º C
FPM / FKM
Medium:
ozone, oxygen, acids, gas, oil & fuel (only with strip insert)
Working pressure PS [bar] L
LS
13.0 170 - 174 12.0 16.5 178 - 182 11.0 15.0 198 - 202 10.0 13.5 217 - 222 9.0 12.0 248 - 253 8.0 11.0 264 - 270 8.0 11.0 270 - 276 7.0 10.0 301 - 307 7.0 9.5 321 - 327 6.0 8.5 353 - 358 5.5 7.5 404 - 409 5.0 6.5 454 - 460 4.5 6.0 505 - 511 4.0 5.5 556 - 562 3.5 5.0 606 - 613 4.0 708 - 715 4.0 758 - 766 3.5 809 - 817 3.5 910 - 918 3.0 1012 - 1020 2.5 1114 - 1122 2.5 1215 - 1224 2.5 1316 - 1325 2.0 1418 - 1427 2.0 1519 - 1529 2.0 1595 - 1605 1621 - 1631 1722 - 1732 1824 - 1834 1925 - 1935 2027 - 2037 STRAUB produces custom
B Width of pipe coupling: FLEX 2 L = 138 mm FLEX 2 LS = 139 mm FLEX 2 LU = 141 mm FLEX 2 LV = 141 mm FLEX 2 H = 142 mm FLEX 2 XS = 148 mm DV Outside diameter of the coupling installed = OD+27 mm C Distance between sealing lips = 91 mm Rmax. Distance between pipe ends with strip insert = 35 mm Distance between pipe ends without strip insert = 10 mm
LU
LV (LDX)
25.0 25.0 25.0 24.0 22.5 22.0 25.0 19.5 25.0 18.5 25.0 17.0 25.0 15.0 25.0 13.0 25.0 12.0 24.0 10.5 22.0 10.0 20.0 8.5 17.0 8.0 16.0 7.5 15.0 6.5 13.0 6.0 11.0 5.5 10.0 5.0 9.0 4.5 8.5 4.0 8.0 4.0 8.0 4.0 7.5 3.0 7.0 3.0 6.5 2.5 6.0 2.0 6.0 2.0 5.5 made couplings
H
Torque rate [Nm] XS
L 10 10 10 10 10 15 15 15 15 15 20 20 20 25 25
LS
LU
LV (LDX)
H
XS
15 15 15 15 15 15 20 20 20 20 20 25 25 25 30 30 30 35 35 40 40 40 40 40 40
30 30 30 30 30 30 30 30 30 30 40 40 40 40 50 50 50 60 60 60 60 60 60 60 60 80 80 90 100 100
40 40 40 40 50 50 60 60 60 70 70 70 80 80 80 90 90 90 90 90 100 100 110 120 120
30 30 30 30 40 40 40 50 50 50 60 60 60 70 70 70 70 70 80 80 85 90 95 100 110
110 110 110 110 120 120 120 140 140 140 160 160 160 160 180 180 180 180 200 200 200 200 220 220 240
25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 22.0 25.0 19.0 25.0 17.0 25.0 16.0 25.0 14.0 25.0 12.0 25.0 12.0 23.5 11.0 22.0 10.0 20.0 9.0 18.0 8.0 16.0 7.0 15.0 7.0 15.0 6.0 14.0 6.0 14.0 6.0 13.0 6.0 13.0 5.5 12.0 5.0 11.0 4.5 10.0 4.0 10.0 from 172.0 up to 2032.0 mm
Remarks: Follow fitting / disassembly instructions Available in one- or two-piece version PS = Working pressure considering the application loads Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Strip inserts are supplied with all couplings sold in Australia L-, LS- and LU-version in W2 or W5 LV(LDX)-version in W5
95
Straub
STRAUB-FLEX 3 Ø 219.1 - 4064.0 mm
Pipe
Clamping range
OD [mm]
[mm]
219.1 250.0 267.0 273.0 304.0 323.9 355.6 406.4 457.2 508.0 558.8 609.6 711.2 762.0 812.8 914.4 1016.0 1117.6 1219.2 1320.8 1422.4 1524.0 1600.0 1625.6 1727.2 1828.8 1930.4 2032.0 2268.0 2540.0 2794.0 3048.0 3302.0 3556.0 3810.0 4064.0
B DV C Rmax.
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +180º C
FPM / FKM
Medium:
ozone, oxygen, acids, gas, oil & fuel (only with strip insert)
Working pressure PS [bar] LS
LV (LDX)
H
18.0 216 - 222 16.0 247 - 253 15.0 264 - 270 15.0 270 - 276 13.0 301 - 307 13.0 25.0 25.0 321 - 327 12.0 25.0 25.0 352 - 358 10.0 25.0 25.0 403 - 409 9.0 25.0 24.0 454 - 460 8.0 23.0 22.0 504 - 512 7.0 21.0 20.0 555 - 562 6.5 19.0 17.0 606 - 613 5.5 16.0 15.0 707 - 715 5.0 15.0 14.0 758 - 766 5.0 14.5 13.0 809 - 817 4.5 12.5 11.5 910 - 918 4.0 11.0 10.5 1012 - 1020 3.5 10.0 9.5 1113 - 1122 3.5 9.0 8.5 1215 - 1224 3.0 9.0 8.0 1316 - 1325 3.0 8.0 7.5 1418 - 1427 2.5 8.0 7.0 1519 - 1529 2.5 7.5 6.5 1595 - 1605 2.5 7.0 6.5 1621 - 1631 2.5 7.0 6.0 1722 - 1732 2.0 6.0 5.5 1824 - 1834 2.0 6.0 5.5 1925 - 1935 2.0 5.5 5.0 2027 - 2037 5.0 4.0 2263 - 2273 4.0 3.5 2535 - 2545 3.5 3.0 2789 - 2799 3.0 3.0 3043 - 3053 2.53 3296 - 3308 2.53 3548 - 3562 2.03 2.53 3804 - 3816 1.53 2.03 4058 - 4070 1.03 2.03 STRAUB produces custom made couplings from
Width of pipe coupling: FLEX 3 LS = 210 mm FLEX 3 LV = 211 mm FLEX 3 H = 212 mm FLEX 3 X = 218 mm Outside diameter of the coupling installed = OD+38 mm Distance between sealing lips = 127 mm Distance between pipe ends with strip insert = 60 mm Distance between pipe ends without strip insert = 15 mm
Torque rate [Nm] X
LS 40 40 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 60 60 60 60 60 60 60 60
25.0 25.0 25.0 25.0 25.0 23.0 20.0 18.0 17.0 16.0 15.0 14.0 13.5 13.0 12.0 11.0 11.0 10.0 9.0 8.0 7.0 6.5 6.0 5.5 5.0 5.0 219.1 up to 4064.0 mm
LV (LDX)
H
X
70 70 70 70 70 70 70 70 70 70 80 80 80 90 90 90 90 90 100 100 110 120 120 130 140 140 150 160 180 200 210
60 60 60 60 60 60 60 60 60 60 80 80 80 100 100 100 100 110 120 120 120 140 140 150 170 180 200 220 230 250 270
90 90 90 90 110 110 125 125 140 140 160 160 160 180 180 200 200 220 240 260 270 290 310 330 340 350
Remarks: Follow fitting / disassembly instructions Available in one or two-piece version PS = Working pressure considering the application loads Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Strip inserts are supplied with all couplings sold in Australia L, LS and LU version in W2 & W5 LV (LDX) version in W5 H & XS version in W1 3
96
Sealing Sleeve
Available in three-piece version only
Straub
STRAUB-OPEN-FLEX 1L Ø 48.3 - 168.3 mm
VX Code VX Code NBR NBR 76399 76400 76401 76402 76403 76404 76405 76406 76407 76408 76409 76410 76411 76412 76413 76414 76415 76416 76417 76418 76419 76420 76421 76422
76423 76424 76425 76426 76427 76428 76429 76430 76431 76432 76433 76434 76435 76436 76437 76438 76439 76440 76441 76442 76443 76444 76445
Sealing Sleeve
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +180º C
FPM / FKM
Medium:
ozone, oxygen, acids, gas, oil & fuel (only with strip insert)
Pipe OD (mm)
Clamping Range (mm)
PS (bar)
B (mm)
C (mm)
DV (mm)
KV (mm)
Pipe Gap with Strip Insert (mm)
Torque rate (Nm)
Allen head (mm)
48.3 54.0 57.0 60.3 73.0 76.1 84.0 88.9 100.6 101.6 104.0 104.8 108.0 114.3 118.0 127.0 129.0 130.2 133.0 139.7 141.3 154.0 159.0 168.3
47.0 - 49.5 52.5 - 55.5 55.5 - 58.5 59.0 - 61.5 71.5 - 74.5 74.5 - 77.5 82.5 - 85.5 87.5 - 90.5 99.0 - 102.5 100.0 - 103.5 102.5 - 105.5 103.0 - 106.5 106.5 - 109.5 112.5 - 116.0 116.0 - 120.0 125.0 - 129.0 127.0 - 131.0 128.5 - 132.0 131.0 - 135.0 138.0 - 141.5 139.5 - 143.0 152.0 - 156.0 157.0 - 161.0 166.0 - 170.5
25.0 25.0 25.0 25.0 25.0 25.0 24.0 24.0 23.0 23.0 22.0 22.0 22.0 21.0 20.0 19.0 18.0 18.0 16.0 16.0 16.0 16.0 16.0 16.0
75 75 75 75 94 94 94 94 94 94 94 94 94 94 94 107 107 107 107 107 107 107 107 107
35 35 35 35 51 51 51 51 51 51 51 51 51 51 51 62 62 62 62 62 62 62 62 62
70 76 79 82 95 98 106 111 123 124 126 127 130 136 140 149 151 152 155 162 163 176 181 190
85 90 95 95 117 122 127 132 147 147 147 147 152 157 162 165 165 165 170 175 180 190 195 205
15 15 15 15 25 25 25 25 25 25 25 25 25 25 25 35 35 35 35 35 35 35 35 35
8 8 8 8 10 10 10 10 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8 8
Height (H): OD 48.3 - 60.3: OD 73.0 - 114.3: OD 127.0 - 168.3:
7.0 mm 9.0 mm 9.5 mm
Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Material Grade W5 316 Stainless Steel Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Strip inserts are supplied with all couplings sold in Australia
97
Straub
STRAUB-OPEN-FLEX 2 Ø 172.0 - 2032.0 mm
Pipe OD (mm)
Clamping Range (mm)
VX Code (LS) EPDM
180.0 200.0 204.0 219.1 235.0 250.0 254.0 267.0 273.0 304.0 317.0 323.9 355.6 406.4 457.2 508.0 558.8 560.0 587.0 609.6 667.0 711.2 762.0 812.8 826.0 914.4 924.0 1016.0 1026.0 1117.0 1219.2 1229.0
178 - 182 198 - 202 202 - 206 217 - 222 233 - 237 248 - 253 252 - 257 264 - 270 270 - 276 301 - 307 314 - 320 321 - 327 353 - 358 404 - 409 454 - 460 505 - 511 556 - 562 557 - 563 584 - 590 606 - 613 664 - 671 708 - 715 758 - 766 809 - 817 822 - 830 910 - 918 920 - 928 1012 - 1020 1022 - 1300 1114 - 1122 1215 - 1224 1225 - 1234
76446 76447 76448 76450
VX Code (LS) NBR
76471
76451 76452
76472
76453 76454 76456 76458 76460 76461
76473 76474 76475 76476 76477
76453 76464 76465 76466 76467 76468
PS (Bar) 16.5 15.0 13.5 13.5 12.0 12.0 11.0 11.0 11.0 10.0 9.5 9.5 8.5 7.5 6.5 6.0 5.5 5.0 5.0 5.0 4.0 4.0 4.0 3.5 3.5 3.5 3.0 3.0 2.5 2.5 2.5 2.5
Sealing Sleeve
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +180º C
FPM / FKM
Medium:
ozone, oxygen, acids, gas, oil & fuel (only with strip insert)
VX Code (LU) EPDM
76480
VX Code (LU) NBR
76498
76481
76482 76483 76484 76486 76487
76488 76489 76490
76499 76500 76501 76502
76503
76492 76493 76494 76495 76496
76497
PS (Bar) 25.0 25.0 25.0 25.0 24.0 24.0 22.5 22.5 22.0 19.5 18.5 18.5 17.0 15.0 13.0 12.0 10.5 10.0 10.0 10.0 8.5 8.5 8.0 7.5 6.5 6.5 6.0 6.0 6.0 5.5 5.0 5.0
Torque rate Torque rate (LS) (LU) 15 15 15 15 15 15 15 15 15 20 20 20 20 20 20 25 25 25 25 25 30 30 30 30 35 35 35 35 40 40 40 40
In the Open-Flex 2 design, Straub produces custom made couplings from 172.0 up to 2032.0 mm STRAUB LV, H & XS are available upon request Available upon request
B DV C Rmax.
98
Width of pipe coupling: OPEN-FLEX 2 L = 138 mm OPEN-FLEX 2 LS = 139 mm OPEN-FLEX 2 LU = 141 mm OPEN-FLEX 2 LV = 141 mm OPEN-FLEX 2 H = 142 mm OPEN-FLEX 2 XS = 148 mm Outside diameter of the coupling installed = OD+27 mm Distance between sealing lips = 91 mm Distance between pipe ends with strip insert = 35 mm Distance between pipe ends without strip insert = 10 mm
Remarks: Follow fitting / disassembly instructions All STRAUB-OPEN-FLEX 2 available in two-piece version PS = Working pressure considering the application loads Material Grade W5 316 Stainless Steel Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Strip inserts are required for special applications 4
One-piece version in slotted design
30 30 30 30 30 30 30 30 30 30 30 30 30 30 40 40 40 40 40 40 40 50 50 50 50 60 60 60 60 60 60 60
Straub
STRAUB-OPEN-FLEX 2 Ø 172.0 - 2032.0 mm
Pipe
Clamping range
OD [mm]
[mm]
172.0 170 - 174 180.0 178 - 182 200.0 198 - 202 219.1 217 - 222 250.0 248 - 253 267.0 264 - 270 273.0 270 - 276 304.0 301 - 307 323.9 321 - 327 355.6 353 - 358 406.4 404 - 409 457.2 454 - 460 508.0 505 - 511 558.8 556 - 562 609.6 606 - 613 711.2 708 - 715 762.0 758 - 766 812.8 809 - 817 914.4 910 - 918 1016.0 1012 - 1020 1117.6 1114 - 1122 1219.2 1215 - 1224 1320.8 1316 - 1325 1422.4 1418 - 1427 1524.0 1519 - 1529 1600.0 1595 - 1605 1625.6 1621 - 1631 1727.2 1722 - 1732 1828.8 1824 - 1834 1930.4 1925 - 1935 2032.0 2027 - 2037 ** Straub Open-Flex 2 L, LV, H & XS are available B DV C Rmax.
Sealing Sleeve
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +180º C
FPM / FKM
Medium:
ozone, oxygen, acids, gas, oil & fuel (only with strip insert)
Working pressure PS [bar] L 13.04 12.04 11.04 10.04 9.04 8.04 8.04 7.04 7.04 6.04 5.54 5.04 4.54 4.04 3.54
LV (LDX)
H
25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 22.0 25.0 19.0 24.0 17.0 22.0 16.0 20.0 14.0 17.0 12.0 16.0 12.0 15.0 11.0 13.0 10.0 11.0 9.0 10.0 8.0 9.0 7.0 8.5 7.0 8.0 6.0 8.0 6.0 7.5 6.0 7.0 6.0 6.5 5.5 6.0 5.0 6.0 4.5 5.5 4.0 upon request.** STRAUB produces
Width of pipe coupling: OPEN-FLEX 2 L = 138 mm OPEN-FLEX 2 LS = 139 mm OPEN-FLEX 2 LU = 141 mm OPEN-FLEX 2 LV = 141 mm OPEN-FLEX 2 H = 142 mm OPEN-FLEX 2 XS = 148 mm Outside diameter of the coupling installed = OD+27 mm Distance between sealing lips = 91 mm Distance between pipe ends with strip insert = 35 mm Distance between pipe ends without strip insert = 10 mm
Torque rate [Nm] XS
L 10 10 10 10 10 15 15 15 15 15 20 20 20 25 25
LV (LDX)
40 25.0 40 25.0 40 25.0 40 25.0 50 25.0 50 25.0 60 25.0 60 25.0 60 25.0 70 25.0 70 23.5 70 22.0 80 20.0 80 18.0 80 16.0 90 15.0 90 15.0 90 14.0 90 14.0 90 13.0 100 13.0 100 12.0 110 11.0 120 10.0 120 10.0 custom made couplings from 172.0
H
XS
30 110 30 110 30 110 30 110 40 120 40 120 40 120 50 140 50 140 50 140 60 160 60 160 60 160 70 160 70 180 70 180 70 180 70 180 80 200 80 200 85 200 90 200 95 220 100 220 110 240 up to 2032.0 mm
Remarks: Follow fitting / disassembly instructions Available in one or two-piece version PS = Working pressure considering the application loads Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Strip inserts are supplied with all couplings sold in Australia L, LS and LU version in W2 & W5 LV (LDX) version in W5 H & XS version in W1
99
Straub
STRAUB-OPEN-FLEX 3 Ø 219.1 - 4064.0 mm
Pipe
Clamping range
OD [mm]
[mm]
100
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Sealing Sleeve
Temp:
-20º C up to +180º C
FPM / FKM
Medium:
ozone, oxygen, acids, gas, oil & fuel (only with strip insert)
Working pressure PS [bar] LS
LV (LDX)
18.0 219.1 216 - 222 16.0 250.0 247 - 253 15.0 267.0 264 - 270 15.0 273.0 270 - 276 13.0 304.0 301 - 307 13.0 25.0 323.9 321 - 327 12.0 25.0 355.6 352 - 358 10.0 25.0 406.4 403 - 409 9.0 25.0 457.2 454 - 460 8.04 508.0 504 - 512 23.0 558.8 555 - 562 7.04 21.0 609.6 606 - 613 6.54 19.0 711.2 707 - 715 5.54 16.0 762.0 758 - 766 5.04 15.0 812.8 809 - 817 5.04 14.5 914.4 910 - 918 4.54 12.5 1016.0 1012 - 1020 4.04 11.0 1117.6 1113 - 1122 3.54 10.0 1219.2 1215 - 1224 3.54 9.0 1320.8 1316 - 1325 3.0 9.0 1422.4 1418 - 1427 3.0 8.0 1524.0 1519 - 1529 2.5 8.0 1600.0 1595 - 1605 2.5 7.5 1625.6 1621 - 1631 2.5 7.0 1727.2 1722 - 1732 2.5 7.0 1828.8 1824 - 1834 2.0 6.0 1930.4 1925 - 1935 2.0 6.0 2032.0 2027 - 2037 2.0 5.5 2268.0 2263 - 2273 5.0 2540.0 2535 - 2545 4.0 2794.0 2789 - 2799 3.5 3048.0 3043 - 3053 3.0 3302.0 3296 - 3308 2.53 3556.0 3548 - 3562 2.03 3810.0 3804 - 3816 1.53 4064.0 4058 - 4070 1.03 ** Straub Open-Flex 3 L, LV, H & XS are available upon request.** B DV C Rmax.
Sealing Sleeve
Width of pipe coupling: OPEN-FLEX 3 LS = 210 mm OPEN-FLEX 3 LV = 211 mm OPEN-FLEX 3 H = 221 mm OPEN-FLEX 3 X = 218 mm Outside diameter of the coupling installed = OD+38 mm Distance between sealing lips = 127 mm Distance between pipe ends with strip insert = 60 mm Distance between pipe ends without strip insert = 15 mm
H
Torque rate [Nm] X
LS
LV (LDX)
H
40 40 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 60 60 60 60 60 60 60 60
X
25.0 70 60 25.0 70 60 25.0 70 60 24.0 70 60 70 60 22.0 70 60 90 20.0 25.0 70 60 90 17.0 25.0 70 60 90 15.0 25.0 70 60 90 14.0 25.0 70 60 110 13.0 25.0 80 80 110 11.5 23.0 80 80 125 10.5 20.0 80 80 125 9.5 18.0 90 100 140 8.5 17.0 90 100 140 8.0 16.0 90 100 160 7.5 15.0 90 100 160 7.0 14.0 90 110 160 6.5 13.5 100 120 180 6.5 13.0 100 120 180 6.0 12.0 110 120 200 5.5 11.0 120 140 200 5.5 11.0 120 140 220 5.0 10.0 130 150 240 4.0 9.0 140 170 260 3.5 8.0 140 180 270 3.0 7.0 150 200 290 3.0 6.5 160 220 310 2.53 6.0 180 230 330 2.53 5.5 200 250 340 2.03 5.0 210 270 350 2.03 5.0 STRAUB produces custom made couplings from 219.1 up to 4064.0 mm Remarks: Follow fitting / disassembly instructions All STRAUB-OPEN-FLEX 3 available in two-piece version PS = Working pressure considering the application loads Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 LS-version in W2 or W5 LV(LDX)-version in W5 H- and X-version in W1 3 Available in three-piece version only 4 One-piece version in slotted design
Straub
STRAUB-FLEX / STRAUB-OPEN-FLEX 3.5 Ø 323.9 - 4064.0 mm
FLEX to 1219.2 mm
Pipe
Clamping range
OD [mm]
[mm]
323.95 355.65 406.45 457.25 508.05 558.85 609.65 655.05 711.25 762.05 812.85 914.45 1016.05 1117.65 1219.25 1422.4 1524.0 1625.0 1727.2 1828.8 1930.4 2032.0 2268.0 2540.0 2794.0 3048.0 3302.0 3556.0 3810.0 4064.0 ** Straub Open-Flex 3.5 L, B DV C Rmax.
FLEX / OPEN-FLEX
Sealing Sleeve
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-20º C up to +80º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
Working pressure PS [bar] H
LV (LDX)
320 - 327 25.0 352 - 370 25.0 25.0 402 - 410 25.0 453 - 461 23.0 504 - 512 21.0 555 - 563 19.0 605 - 614 17.0 651 - 659 16.0 707 - 715 15.0 758 - 766 14.0 809 - 817 12.0 910 - 918 11.0 1011 - 1021 10.0 1112 - 1123 9.0 1214 - 1224 7.0 1417 - 1427 7.0 1519 - 1529 6.0 1620 - 1630 6.0 1722 - 1732 5.0 1824 - 1834 4.5 1925 - 1935 4.0 2026 - 2038 3.5 2262 - 2274 3.0 2534 - 2546 2.5 1788 - 2800 2.0 3042 - 3054 1.53 3296 - 3308 3550 - 3562 1.53 3804 - 3816 1.03 4058 - 4070 1.03 LV, H & XS are available upon request.**
Width of pipe coupling: FLEX / OPEN-FLEX 3.5 LV = 310 mm FLEX / OPEN-FLEX 3.5 H = 311 mm Outside diameter of the coupling installed = OD+38 mm Distance between sealing lips = 227 mm Distance between pipe ends with strip insert = 120 mm Distance between pipe ends without strip insert = 20 mm
Torque rate [Nm] H
LV (LDX)
25.0 25.0 25.0 25.0 23.0 21.0 19.0 17.0 16.0 15.0 14.0 12.0 11.0 10.0 9.0 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 3.03 3.03 2.53 2.53 STRAUB produces custom made
50 50 50 50 50 50 50 50 50 50 50 60 60 70 80 80 80 90 90 110 110 120 130 140 140 160 170 180 190 210 couplings from 323.9 up
50 50 50 50 50 50 50 50 50 50 50 60 60 70 80 80 80 90 90 100 110 120 130 140 140 160 170 180 190 210 to 4064.0 mm
Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Strip inserts are required for special applications (included) LV(LDX)-version in W5 H-version in W1 3 5
Available in three-piece version only STRAUB-FLEX available in one-piece version as well
101
Straub
STRAUB-FLEX / STRAUB-OPEN-FLEX 4 Ø 323.9 - 4064.0 mm
FLEX to 812.0 mm
Pipe
Clamping range
OD [mm]
[mm]
323.95 355.65 406.45 457.25 508.05 558.85 609.65 655.05 711.25 762.05 812.85 914.4 1016.0 1117.6 1219.2 1422.4 1524.0 1625.0 1727.2 1828.8 1930.4 2032.0 2268.0 2540.0 2794.0 3048.0 3302.0 3556.0 3810.0 4064.0 ** Straub Open-Flex 4 L, B DV C Rmax.
FLEX / OPEN-FLEX
Working pressure PS [bar] H
LV (LDX)
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Torque rate [Nm] LV (LDX)
320 - 327 25.0 25.0 40 352 - 359 25.0 25.0 40 25.0 25.0 40 403 - 409 24.0 25.0 40 454 - 460 22.0 23.0 40 505 - 512 20.0 21.0 40 555 - 562 19.0 19.0 40 606 - 613 18.0 18.0 40 652 - 658 16.0 17.0 40 707 - 715 15.0 16.0 40 758 - 766 14.0 14.0 50 809 - 817 12.0 13.0 50 910 - 918 10.0 11.0 60 1012 - 1020 10.0 10.0 60 1113 - 1122 9.0 9.0 70 1215 - 1224 7.0 8.0 70 1418 - 1427 6.0 7.0 80 1519 - 1529 6.0 7.0 80 1621 - 1631 6.0 7.0 90 1722 - 1732 5.0 6.0 100 1824 - 1834 5.0 6.0 110 1925 - 1935 4.0 5.0 120 2027 - 2037 3.5 4.5 130 2263 - 2273 3.0 4.0 140 2535 - 2545 3.0 3.0 140 2798 - 2799 2.0 3.0 160 3043 - 3053 2.03 170 3296 - 3308 3.03 180 3548 - 3562 1.53 2.53 190 3804 - 3816 1.03 2.03 210 4058 - 4070 1.03 2.03 LV, H & XS are available upon request.** STRAUB produces custom made couplings from 323.9 up
Width of pipe coupling: FLEX / OPEN-FLEX 4 LV = 443 mm FLEX / OPEN-FLEX 4 H = 444 mm Outside diameter of the coupling installed = OD+48 mm Distance between sealing lips = 350 mm Distance between pipe ends with strip insert = 200 mm Distance between pipe ends without strip insert = 20 mm
H 40 40 40 40 40 40 40 40 40 40 50 50 60 60 70 70 80 80 90 100 110 120 130 140 140 160 170 180 190 210 to 4064.0 mm
Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Strip inserts are required for special applications (included) LV(LDX)-version in W5 H-version in W1 3 5
102
Sealing Sleeve
Available in three-piece version only STRAUB-FLEX available in one-piece version as well
Straub
STRAUB-STEP-FLEX 2 Ø 250.0 - 812.8 mm
Pipe 1
Pipe 2
OD [mm]
[min - max]
250.0 267.0 273.0 304.0 323.9 355.6 406.4 457.2 508.0 558.8 609.6 711.2 762.0 812.8
Sealing Sleeve
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Working pressure PS [bar] LS
LU
LV (LDX)
H
Torque rate [Nm] XS
12.0 24.0 220 - 280 11.0 22.5 237 - 297 11.0 22.0 25.0 25.0 25.0 243 - 303 10.0 19.5 25.0 25.0 25.0 274 - 334 9.5 18.5 25.0 25.0 25.0 293 - 353 8.5 17.0 25.0 25.0 25.0 325 - 385 7.5 15.0 25.0 22.0 25.0 376 - 436 6.5 13.0 25.0 19.0 25.0 427 - 487 6.0 12.0 24.0 17.0 25.0 478 - 538 5.5 10.5 22.0 16.0 25.0 528 - 588 5.0 10.0 20.0 14.0 25.0 579 - 639 4.0 8.5 17.0 12.0 25.0 681 - 741 4.0 8.0 16.0 12.0 23.5 732 - 792 3.5 7.5 15.0 11.0 22.0 782 - 842 STRAUB produces custom made couplings from 250.0 up to
B Width of pipe coupling: STEP-FLEX 2 LS = 139 mm STEP-FLEX 2 LU = 141 mm STEP-FLEX 2 LV = 141 mm STEP-FLEX 2 H = 142 mm STEP-FLEX 2 XS = 148 mm DV Outside diameter of the coupling installed = OD+27 mm C Distance between sealing lips = 91 mm Rmax. Distance between pipe ends with strip insert = 35 mm Distance between pipe ends without strip insert = 10 mm
LS
LU
15 30 15 30 15 30 20 30 20 30 20 30 20 30 20 40 25 40 25 40 25 40 30 50 30 50 30 50 812.8 mm
LV (LDX)
H
XS
40 40 40 40 50 50 60 60 60 70 70 70
30 30 30 30 40 40 40 50 50 50 60 60
110 110 110 110 120 120 120 140 140 140 160 160
Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Stainless steel strip insert included LS- and LU-version in W2 or W5 LV(LDX)-version in W5 H- and XS-version in W1
103
Straub
STRAUB-STEP-FLEX 3 Ø 914.4 - 4064.0 mm
Pipe 1
Pipe 2
OD [mm]
[min - max]
914.4 1016.0 1117.6 1219.2 1320.8 1422.4 1524.0 1600.0 1625.4 1727.2 1828.8 1930.4 2032.0 2268.0 6 2540.0 6 2794.0 6 3048.0 6 3302.0 6 3556.0 6 3810.0 6 4064.0 6
B DV C Rmax.
Temp:
-20º C up to +100º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Working pressure PS [bar] LS
4.5 12.5 11.5 884 - 944 4.0 11.0 10.5 986 - 1046 3.5 10.0 9.5 1087 - 1147 3.5 9.0 8.5 1189 - 1249 3.0 9.0 8.0 1290 - 1350 3.0 8.0 7.5 1392 - 1452 2.5 8.0 7.0 1494 - 1554 2.5 7.5 6.5 1570 - 1630 2.5 7.0 6.5 1595 - 1655 2.5 7.0 6.0 1697 - 1757 2.0 6.0 5.5 1798 - 1858 2.0 6.0 5.5 1900 - 1960 2.0 5.5 5.0 2002 - 2062 2238 - 2298 2510 - 2570 2764 - 2824 3018 - 3078 3272 - 3332 3526 - 3586 3780 - 3840 4034 - 4094 STRAUB produces custom made couplings from
Width of pipe coupling: STEP-FLEX 3 LS = 210 mm STEP-FLEX 3 LV = 211 mm STEP-FLEX 3 H = 212 mm STEP-FLEX 3 X = 218 mm Outside diameter of the coupling installed = OD+38 mm Distance between sealing lips = 127 mm Distance between pipe ends with strip insert = 60 mm Distance between pipe ends without strip insert = 15 mm
Torque rate [Nm]
H
LV (LDX)
X
LS
23.0 50 20.0 50 18.0 50 17.0 50 16.0 50 15.0 60 14.0 60 13.5 60 13.0 60 12.0 60 11.0 60 10.0 60 10.0 60 9.0 8.0 7.0 6.5 6.0 5.5 5.0 5.0 914.4 up to 4064.0 mm
LV (LDX)
H
X
80 80 80 90 90 90 90 90 100 100 110 120 120
80 80 80 100 100 100 100 110 120 120 120 140 140
110 125 125 140 140 160 160 170 180 180 200 200 220 240 260 270 290 310 330 340 350
Remarks: Follow fitting / disassembly instructions PS = Working pressure considering the application loads Test pressure = PS x 1.5 (for example industry, water supply etc.) Burst pressure = approx. PS x 2 Stainless steel strip insert included Available in one-piece version only LS-version in W2 or W5 LV(LDX)-version in W5 H- and X-version in W1 6
104
Sealing Sleeve
On request
Straub
STRAUB-CLAMP SCE Ø 44.0 - 330.0 mm
Pipe OD (mm)
Clamping Range (mm)
PN (bar)
VX Code NBR
2 Lock Bolts (mm)
44.0 48.0 54.0 60.0 67.0 70.0 75.0 82.0 87.0 88.0 95.0 108.0 113.0 118.0 120.0 132.0 135.0 139.0 145.0 159.0 167.0 176.0 193.0 215.0 228.0 240.0 261.0 269.0 280.0 315.0 320.0
44 - 48 48 - 52 54 - 58 60 - 67 67 - 74 70 - 77 75 - 83 82 - 89 87 - 95 88 - 98 95 - 104 108 - 118 113 - 123 118 - 128 120 - 131 132 - 142 135 - 145 139 - 149 145 - 155 159 - 170 167 - 178 176 - 187 193 - 203 215 - 225 228 - 239 240 - 250 261 - 271 269 - 280 280 - 291 315 - 325 320 - 330
16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0
76517 76518 76519 76520
200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200
76521 76522 76523 76524 76525 76526 76527 76528 76529
76530 76531 76532 76533 76534 76535 76536
76537
Clamp length
Rmax
200 mm 300 mm 400 mm
50 mm 150 mm 250 mm
Sealing Sleeve
Temp:
-5º C up to +40º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-5º C up to +40º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
VX Code NBR
76538
76539 76540 76541 76542 76543 76544 76545 76546
3 Lock Bolts (mm) 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300
VX Code NBR
4 Lock Bolts (mm)
400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400
Available upon request Remarks: Follow fitting instructions Different pipe diameters (transition) are not possible Material Grade W4 304 Stainless Steel Test pressure = PN x 1.5 Radial length of damaged area max. 20% of pipe outside diameters The repair clamp must be centred over the damaged area
105
Straub
STRAUB-CLAMP SCZ Ø 88.0 - 440.0 mm
Pipe OD (mm)
Clamping Range (mm)
PN (bar)
88.0 100.0 108.0 114.0 120.0 130.0 140.0 159.0 168.0 190.0 210.0 218.0 240.0 269.0 282.0 315.0 322.0 337.0 347.0 365.0 390.0 410.0 420.0
88 - 110 100 - 120 108 - 128 114 - 134 120 - 140 130 - 150 140 - 160 159 - 180 168 - 189 190 - 210 210 - 230 218 - 238 240 - 260 269 - 289 282 - 302 315 - 335 322 - 344 337 - 358 347 - 367 365 - 385 390 - 410 410 - 430 420 - 440
16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 6.0 6.0 5.0 5.0 5.0 5.0
VX Code NBR
Available upon request Remarks: Follow fitting / disassembly instructions Different pipe diameters (transition) are not possible Material Grade W4 304 Stainless Steel Test pressure = PN x 1.5 Radial length of damaged area max. 20% of pipe outside diameters The repair clamp must be centered over the damaged area Working pressure for gas: max. 5 bar
106
2 Lock Bolts (mm)
Clamp length
Rmax
200 mm 300 mm 400 mm
50 mm 150 mm 250 mm
Sealing Sleeve
Temp:
-5º C up to +40º C
EPDM
Medium:
all qualities of water, waste water, air, solids and chemical products
Sealing Sleeve
Temp:
-5º C up to +40º C
NBR
Medium:
water, gas, oil, fuel and other hydrocarbons
VX Code NBR
200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 76547
3 Lock Bolts (mm) 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300
VX Code NBR
76548 76549 76550 76551 76552
4 Lock Bolts (mm) 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400
Notes
iv
Vinidex Pty Limited ABN 42 000 664 942 HEAD OFFICE Level 4, 26 College Street Darlinghurst NSW 2010 PO Box 747, Darlinghurst NSW 1300
CUSTOMER SERVICE P 13 11 69 | F 13 24 43 E
[email protected] W www.vinidex.com.au
Reception: +61 2 8278 0500
AUSTRALIAN OPERATIONS Sydney
Adelaide
Townsville
Darwin
254 Woodpark Rd Smithfield NSW 2164
9–11 Kaurna Ave Edinburgh SA 5111
49 Enterprise Ave Bohle QLD 4816
3846 Marjorie St Pinelands NT 0829
Wagga Wagga
Launceston
Toowoomba
Perth
280 Byrnes Rd Wagga Wagga NSW 2650
15 Thistle St Sth Launceston TAS 7249
Lot 2 Witmack Rd Wellcamp QLD 4350
Sainsbury Rd O’Connor WA 6163
Melbourne
Brisbane
Rodney Industries
Unit 1, 10 Duerdin St Notting Hill VIC 3168
224 Musgrave Rd Coopers Plains QLD 4108
19 Valente Close Chermside QLD 4032
231-245 St Albans Rd Sunshine VIC 3020
VIN32020161001
Limitation of Liability This product catalogue has been compiled by Vinidex Pty Limited (“the Company”) to promote better understanding of the technical aspects of the Company’s products to assist users in obtaining from them the best possible performance. The product catalogue is supplied subject to acknowledgement of the following conditions: 1 The product catalogue is protected by copyright and may not be copied or reproduced in any form or by any means in whole or in part without prior consent in writing by the Company. 2 Product specifications, usage data and advisory information may change from time to time with advances in research and field experience. The Company reserves the right to make such changes at any time without further notice. 3 Correct usage of the Company’s products involves engineering judgements, which can not be properly made without full knowledge of all the conditions pertaining to each specific installation. The Company expressly disclaims all and any liability to any person whether supplied with this publication or not in respect of anything and all of the consequences of anything done or omitted to be done by any such person in reliance whether whole or part of the contents of this publication. 4 No offer to trade, nor any conditions of trading, are expressed or implied by the issue of content of this product catalogue. Nothing herein shall override the Company’s Condition of Sale, which may be obtained from the Registered Office or any Sales Office of the Company. 5 This product catalogue is and shall remain the property of the Company, and shall be surrendered on demand to the Company. 6 Information supplied in this product catalogue does not override a job specification, where such conflict arises; consult the authority supervising the job. © Copyright Vinidex Pty Limited.