Idea Transcript
STANDARDILUETTELO
1(15)
Tarkistuspäivämäärä
12.10.2006
Kpl
Standardin numero
Vahvistus- Otsikko pvm
Voimassa
Uusi/korvaava standardi
STANDARDS FOR THE MATERIALS 1
EN 10204
2004-10
Metallic products.Types of inspection documents
X
2
EN 10079
1992-10
Definition of steel products
X
3
EN 10027-1
2005-08
Designation systems for steel. Part 1: Steel names, principal symbols
X
4
EN 10027-2
1992-07
Designation systems for steel. Part 2: Numerical system
X
5
EN 10056-1
1998-08
Structural steel equal and unequal leg angles Part 1: Dimensions
X
6
EN 10056-2
1993-09
Structural steel equal and unequal leg angles Part 2: Tolerances on shape and dimensions
X
7
EN 10025
1990-03
Hot rolled products of non-alloy structural steels. Technical delivery conditions
8
EN 10029
1991-04
Hot rolled steel plates 3mm thick or above. Tolerances on dimensions, shape and mass
X
9
EN 10051
1997-09
Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels. Tolerances on dimensions and shape
X
10
EN 10034
1993-09
Structural steel I and H section- Tolerances on shape and dimensions
X
11
EN 10163-1
2004-12
Delivery requirements for surface condition of hot rolled steel plates, wide flats and sections Part 1: General requirements
X
EN 10025-1:2004 Hot rolled products of structural steels. Part 1: General technical delivery conditions EN 10025-2:2004 Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels + Korjaus EN 10025-2/AC:2005
STANDARDILUETTELO
2(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
12
EN 10163-2
2004-12
EN 10163-3
Delivery requirements for surface condition of hot rolled steel plates, wide flats and sections Part 2: Plate and wide flats
Voimassa
Uusi/korvaava standardi
X
13
EN 10219-1
2003-02
Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 1 : Technical delivery requirements
EN 10219-1:2006-04
14
EN 10219-2
2003-02
Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 2 : Tolerances, dimensions and sectional properties
EN 10219-1:2006-04
15
EN 10279
2000-01
Hot-rolled steel channels. Tolerances on shape, dimensions and mass
16
EN 10113-1
1993-03
Hot-rolled products in weld able fine grain structural steels
X EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions EN 10025-3:2004 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels EN 10025-4:2004 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
17
EN 10113-2
1993-03
Hot-rolled products in weld able fine grain structural steels
EN 10025-1:2004 EN 10025-3:2004
18
EN 10113-3
1993-03
Hot-rolled products in weld able fine grain structural steels
EN 10025-1:2004 EN 10025-4:2004
19
EN 10155
1993-06
Structural steels with improved athmospheric corrosion resistance. Technical delivery conditions
EN 10025-5:2004 Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
STANDARDILUETTELO
3(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
Voimassa
20
ISO 4014
1999-09
Hexagon head bolts. Product grades A and B
X
21
EN 24014
1991-10
Hexagon head bolts. Product grades A and B
X
22
ISO 4017
1999-08
Hexagon head screws. Product grades A and B
X
23
EN 24017
1991-10
Hexagon head screws. Product grades A and B
X
24
ISO 4032
1999-08
Hexagon nuts, style 1. Product grades A and B
X
25
EN 24032
1991-10
Hexagon nuts, style 1. Product grades A and B
X
26
ISO 8992
2005-04
Fasteners. General requirements for bolts, screws, studs and nuts
X
27
ISO 7091
2000-06
Plain washers. Normal series. Product grade C
X
28
ISO 4759-1
2000-11
Tolerances for fasteners. Part 1: Bolts, screws, studs and nuts. Product grades A, B and C
X
29
EN 10130 + A1
1998-09
Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions
X
30
ISO 898-1
1999-08
Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs
X
31
ISO 898-2
1992-11
Mechanical properties of fasteners. Part 2: Nuts with specified proof load values. Coarse thread
X
32
ISO 898-5
1998-08
Mechanical properties of fasteners made of carbon steel and alloy steel. Part 5: Set screws and similar threaded fasteners not under tensile stresses
X
33
ISO 898-6
1994-12
Mechanical properties of fasteners. Part 6: Nuts with specified proof load values. Fine pitch thread
X
34
ISO 898-7
1992-11
Mechanical properties of fasteners. Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
X
35 X
Uusi/korvaava standardi
Uusi versio valmistunee joulukuussa 2006
STANDARDILUETTELO
4(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
Voimassa
Uusi/korvaava standardi
STANDARDS FOR THE WELDING PROCEDURE SPECIFICATION 36
EN 288-1
1992-02
Specification and qualification of welding procedures for metallic materials Part 1: General rules for fusion welding
EN ISO 15607:2003
37
EN 288-2
1992-02
Specification and qualification of welding procedures for metallic materials Part 2: Welding procedure specification for arc welding
EN ISO 15609-1:2004
38
EN 288-3
1992-02
Specification and qualification of welding procedures for metallic materials Part 3: Welding procedure tests for the arc welding of steels
EN ISO 15614-1:2004
39
EN 288-5
1994-08
Specification and qualification of welding procedures for metallic materials Part 5: Approval by using approved welding consumables for arc welding
EN ISO 15610:2003
40
EN 288-6
1994-08
Specification and qualification of welding procedures for metallic materials Part 6: Approval related to previous experience
EN ISO 15611:2003
41
EN 288-7
1995-05
Specification and qualification of welding procedures for metallic materials Part 7: Approval by a standard welding procedure for arc welding
EN ISO 15612:2004
42
EN 288-8
1995-05
Specification and qualification of welding procedures for metallic materials Part 8: Approval by a pre-production welding test
EN ISO 15613:2004
43
EN 29692
1994-02
Metal- arc welding with covered electrode, gas-shielded metal-arc and gas welding. Joint preparations for steel
EN ISO 9692-1:2003 Welding and allied processes. Recommendations for joint preparation. Part 1: Manual metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels
44
EN ISO 9692-2
1998-04
Welding and allied processes. Joint preparations Part 2: Submerged arc welding of steels
X
45
EN ISO 13920
1996-08
Welding. General tolerances for welded constructions. Dimensions for lengths and angles. Shape and position
X
46
ENV 1090-1
1996-04
Execution of steel structures Part 1: General rules and rules for buildings
X
47
SFS-EN 1011-1
1998-08
Welding. Recommendations for welding of metallic materials. Part 1: General guidance for arc welding
X
+ Korjaus EN ISO 9692-2/AC:1999
+ Lisäys A1:2002-09 + Lisäys A2:2004-02
STANDARDILUETTELO
5(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko Voimassa pvm Welding. Recommendations for welding of metallic materials. Part 2: Arc 2001-05 X welding of ferritic steels Welding. Recommendations for welding of metallic materials. Part 3: Arc 2001-03 X welding of stainless steels Welding. Recommendations for welding of metallic materials. Part 4: Arc 2001-03 X welding of aluminium and aluminium alloys Welding. Recommendations for welding of metallic materials. Part 5: Welding 2003-12 X of clad steel Welding. Recommendation for welding of metallic materials. Part 6: Laser 2006-01 X beam welding Welding. Recommendations for welding of metallic materials. Part 7: Electron 2004-09 X beam welding Welding. Recommendations for welding of metallic materials. Part 8: Welding 2005-03 X of cast irons
48
SFS-EN 1011-2
49
SFS-EN 1011-3
50
SFS-EN 1011-4
51
SFS-EN 1011-5
52
SFS-EN 1011-6
53
SFS-EN 1011-7
54
SFS-EN 1011-8
55
SFS-EN 439
1995-02
Welding consumables. Shielding gases for arc welding and cutting
X
56
SFS-EN ISO 4063
2000-05
Welding and allied processes. Nomenclature of processes and reference numbers
X
57
SFS-EN ISO 6947
1997-08
Welds. Working positions. Definitions of angles of slope and rotation
X
58
EN ISO 15607
2003-12
Welding Specification and qualification of welding procedures for metallic materials. General rules
X
59
CEN ISO/TR 15608
2005-10
Welding. Guidelines for a metallic materials grouping system
X
60
SFS-EN ISO 15609-1 2004-11
Specification and qualification of welding procedures for metallic materials. Welding procedure specification. Part 1: Arc welding
X
61
SFS-EN ISO 15609-2 2002-03
Specification and qualification of welding procedures for metallic materials. Welding procedure specification. Part 2: Gas welding
X
62
SFS-EN ISO 15609-3 2004-09
Specification and qualification of welding procedures for metallic materials. Welding procedures specification. Part 3: Electron beam welding
X
63
SFS-EN ISO 15609-4 2004-09
Specification and qualification of welding procedures for metallic materials. Welding procedure specification. Part 4: Laser beam welding
X
64
SFS-EN ISO 15609-5 2004-09
Specification and qualification of welding procedures for metallic materials. Welding procedure specification. Part 5: Resistance welding
X
Uusi/korvaava standardi + Lisäys A1:2004-02 + Lisäys A1:2004-02 + Lisäys A1:2004-02
STANDARDILUETTELO
6(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
Voimassa
65
EN ISO 15610
2003-11
Specification and qualification of welding procedures for metallic materials. Qualification based on tested welding consumables
X
66
EN ISO 15611
2003-12
Specification and qualification of welding procedures for metallic materials. Qualification based on previous welding experience
X
67
EN ISO 15612
2004-08
Specification and qualification of welding procedures for metallic materials. Qualification by adoption of a standard welding procedure
X
68
EN ISO 15613
2004-06
Specification and qualification of welding procedures for metallic materials. Qualification based on pre-production welding test
X
69
ISO 15614-1
2004-06
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
X
Uusi/korvaava standardi
+ Corrigendum 1:2005
70
ISO 15614-2
2005-05
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 2: Arc welding of aluminium and its alloys
X
71
ISO 15614-4
2005-07
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 4: Finishing welding of aluminium castings
X
72
ISO 15614-5
2004-03
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 5: Arc welding of titanium, zirconium and their alloys
X
73
ISO 15614-8:
2002-04
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 8: Welding of tubes to tube-plate joints
X
74
ISO 15614-10
2005-02
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 10: Hyperbaric dry welding
X
75
ISO 15614-11
2002-03
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 11: Electron and laser beam welding
X
76
ISO 15614-12
2004-08
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 12: Spot, seam and projection welding
X
77
ISO 15614-13
2005-02
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 13: Resistance butt and flash welding
X
+ Corrigendum 1:2005
STANDARDILUETTELO
7(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
78
ISO 15614-6
2006-04
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 6: Arc and gas welding of copper and its alloys
79
EN ISO 14555
1998-10
Welding. Arc stud welding of metallic materials
80
EN ISO 15620
2000-07
Welding. Friction welding of metallic materials
Voimassa
Uusi/korvaava standardi
X X
Uusi versio valmistunee sysksyn aikana
X
STANDARDS FOR THE PREPARATION OF STEEL 81
ISO 9223
1992-02
Corrosion of metals and alloys. Corrosivity of atmospheres. Classification
X
82
EN 10238
1996-09
Automatically blast-cleaned and automatically prefabrication primed structural steel products
X
83
ISO 8501-1
1988-12
Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
X
Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 2: Preparation grades of previously coated steel substrates after localized removal of previous coatings
X
84
ISO 8501-2
1994-12
85
ISO 8501-3
2001-12
Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 3: Preparation grades of welds, cut, edges and other areas with surface imperfections
86
ISO 8503-1
1988-02
Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces
Uusi versio ilmestynee lähiaikoina
ISO 8501-3:2006-03 Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 3: Preparation grades of welds, edges and other areas with surface imperfections
X
STANDARDILUETTELO
8(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
87
ISO 8503-2
1988-02
88
89
ISO 8503-3
ISO 8503-4
1988-02
1988-02
Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 3: Method for the calibration of ISO reference comparators and for determination of surface profile. Focusing microscope procedure Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 4: Method for the calibration of ISO reference comparators and for determination of surface profile. Stylus instrument procedure
Voimassa
X
X
X
90
EN ISO 8504-1
2001-05
Preparation of steel substrates before application of paints and related products. Surface preparation methods. Part1: General principles
X
91
EN ISO 8504-2
2001-05
Preparation of steel substrates before application of paints and related products. Surface preparation methods. Part 2: Abrasive blast cleaning
X
92
EN ISO 8504-3
2001-05
Preparation of steel substrates before application of paints and related products. Surface preparation methods. Part 3: Hand- and power- tools cleaning
X
Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 1: General principles and rating schemes
X
Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 2: Designation of degree of blistering
X
Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 3: Designation of degree of rusting
X
Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 4: Designation of degree of cracking
X
93
94
95
96
ISO 4628-1
ISO 4628-2
ISO 4628-3
ISO 4628-4
2003-09
2003-09
2003-09
2003-09
Uusi/korvaava standardi
STANDARDILUETTELO
9(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
97
ISO 4628-5
2003-09
Voimassa
Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 5: Designation of degree of flaking
X
98
EN ISO 9013
2002-09
Welding and allied processes. Quality classification and dimensional tolerances of thermally cut (oxygen/fuel gas flame) surfaces
X
99
EN ISO 12944-1
1998-05
Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 1: General introduction
X
100 EN ISO 12944-2
1998-05
Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 2: Classification of environments
X
101 EN ISO 12944-3
1998-05
Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 3: Design considerations
X
102 EN ISO 12944-4
1998-05
Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 4: Types of surface and surface preparation
X
103 EN ISO 12944-5
1998-05
Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 5: Protective paint system
X
104 EN ISO 12944-6
1988-05
Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 6: Laboratory performance test methods
X
105 EN ISO 12944-7
1998
Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 7: Execution and supervision of paint work
X
106 EN ISO 12944-8
1998-05
Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 8: Development of specifications for new work and maintenance
X
107 EN ISO 1460
1994-10
Metallic coatings. Hot dip galvanized coatings on ferrous materials. Gravimetric determination of the mass per unit area (ISO 1460:1992)
X
108 EN ISO 1461
1999-02
Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods
X
109 EN ISO 14713
1999-03
Protection against corrosion of iron and steel in structures. Zinc and aluminium coatings. Guidelines
X
Uusi/korvaava standardi
+ Lisäys A1:2003
STANDARDILUETTELO
10(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
110 ISO 7413
Vahvistus- Otsikko pvm 1984-11
111 ISO 2808
Voimassa
Hexagon nuts for structural bolting, style 1, hot-dip galvanized (oversize tapped). Product grades A and B. Property classes 5, 6 and 8
X
Paints and varnishes -- Determination of film thickness
X
112 EN ISO 2178
1995-01
Non-magnetic coatings on magnetic substrates. Measurement of coating thickness- Magnetic method
X
113 EN ISO 2064
2000-03
Metallic and other inorganic coatings. Definitions and conventions concerning the measurement of thickness
X
114 ISO 15184
1998-11
Paints and varnishes. Determination of film hardness by pencil test
X
115 ISO 7253
1996-12
Paints and varnishes. Determination of resistance to neutral salt spray (fog)
116 SFS-EN ISO 4892-1
2001-01
Plastics. Methods of exposure to laboratory light sources. Part 1: General guidance
X
117 SFS-EN ISO 4892-2
2006-08
Plastics. Methods of exposure to laboratory light sources. Part 2: Xenon-arc lamps
X
118 SFS-EN ISO 4892-3
2006-08
Plastics. Methods of exposure to laboratory light sources. Part 3: Fluorescent UV lamps
X
Uusi/korvaava standardi
ISO 9227:2006 Corrosion tests in artificial atmospheres.Salt spray tests
STANDARDS FOR THE QUALITY REQUIRMENTS 119 EN 729-1
1994-09
Quality requirements for welding. Fusion welding of metallic materials. Part 1: Guidelines for selection and use
EN ISO 3834-1:2005 Quality requirements for fusion welding of metallic materials. Part 1: Criteria for the selection of the appropriate level of quality requirements
120 EN 729-3
1994-09
Quality requirements for welding. Fusion welding of metallic materials. Part 3: Standard quality requirements
EN ISO 3834-3:2005 Quality requirements for fusion welding of metallic materials. Part 3: Standard quality requirements
STANDARDILUETTELO
11(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
121 EN 729-4
1994-09
Quality requirements for welding. Fusion welding of metallic materials. Part 4: Elementary quality requirements
122 EN 719
1994-08
Welding coordination. Tasks and responsibilities
123 EN 287-1
1992-02
Approval testing of welders. Fusion welding. Part 1: Steels
124 EN 1418
1997-12
Welding personnel. Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials
125 EN 473
1993-01
Voimassa
Uusi/korvaava standardi EN ISO 3834-4:2005 Quality requirements for fusion welding of metallic materials. Part 4: Elementary quality requirements
X EN 287-1:2004 Qualification test of welders. Fusion welding. Part 1: Steels + Korjaus AC:2004 + Lisäys A2:2006 X EN 473:2000 Non destructive testing. Qualification and certification of NDT personnel. General principles + Lisäys A1:2005
Qualification and certification of NDT personel. General principles
STANDARDS FOR THE QUALITY LEVEL 126 EN 25817
1992-07
EN ISO 5817:2003 Welding. Fusionwelded joints in steel, nickel, titanium and their alloys (beam welding excluded). Quality levels for imperfections + Korjaus AC:2006
Arc-welded joints in steel. Guidance on quality levels for imperfection
STANDARDS FOR THE INSPECTION INSTRUCTION 127 EN 12062
1997-08
Non-destructive examination of welds. General rules for metallic materials
X
128 EN 970
1997-02
Non–destructive examination of fusion welds. Visual examination
X
129 EN ISO 6520-1
1998-10
Welding and allied processes. Classification of geometrical imperfections in metallic materials. Part 1 : Fusion welding
X
+ Lisäys A1:2002 + Lisäys A2:2003
STANDARDILUETTELO
12(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
Voimassa
Uusi/korvaava standardi + Lisäys A1:2002 + Lisäys A2:2004
130 SFS-EN 1289
1998-08
Non-destructive examination of welds. Penetrant testing of welds. Acceptance levels
X
131 SFS-EN 571-1
1997-08
Non destructive testing. Penetrant testing. Part 1: General principles
X
132 EN 1290
1998-02
Non-destructive examination of welds. Magnetic particle examination of welds
X
133 EN 1291
1998-02
Non-destructive examination of welds. Magnetic particle testing of welds. Acceptance levels
X
+ Lisäys A1:2002 + Lisäys A2:2003 + Lisäys A1:2002 + Lisäys A2:2003
134 SFS-EN 1435
1998-01
Non-destructive examination of welds. Radiographic examination of welded joints
X
+ Lisäys A1:2002 + Lisäys A2:2004
135 EN 12517-1
2006-03
Non-destructive testing of welds. Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography. Acceptance levels
X
136 SFS-EN 1712
1998-03
Non-destructive examination of welds. Ultrasonic examination of welded joints. Acceptance levels
X
137 SFS-EN 1713
1998-12
Non-destructive examination of welds. Ultrasonic examination
X
138 SFS-EN 1714
1998-03
Non-destructive examination of welds. Ultrasonic examination of welded joints
X
+ Lisäys A1:2002 + Lisäys A2:2004 + Lisäys A1:2002 + Lisäys A2:2004
139 SFS-EN 13480-1
2002-09
Metallic industrial piping. Part 1: General
X
+ Lisäys A1:2006
140 SFS-EN 13480-2
2002-12
Metallic industrial piping. Part 2: Materials
X
141 SFS-EN 13480-3
2002-09
Metallic industrial piping. Part 3: Design and calculation
X
142 SFS-EN 13480-4
2002-09
Metallic industrial piping. Part 4: Fabrication and installation
X
143 SFS-EN 13480-5
2002-09
Metallic industrial piping. Part 5: Inspection and testing
X
144 SFS-EN 13480-6
2005-03
Metallic industrial piping. Part 6: Additional requirements for buried piping
X
145 CEN/TR 13480-7
2002-05
Metallic industrial piping. Part 7: Guidance on the use of conformity assessment procedures
X
146 SFS-EN 1043-1
1996-05
Destructive tests on welds in metallic materials. Hardness testing. Part 1: Hardness test on arc welded joints
X
+ Lisäys A1:2002 + Lisäys A2:2004
+ Lisäys A1:2006
+ Lisäys A1:2006
STANDARDILUETTELO
13(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
Voimassa
147 SFS-EN 1043-2
1997-05
Destructive tests on welds in metallic materials. Hardness test. Part 2: Micro hardness testing on welded joints
X
148 EN 444
1994-02
Non-destructive testing. General principles for radiographic examination of metallic materials by X- and gamma-rays
X
Uusi/korvaava standardi
STANDARDS FOR THE DESIGN 149 ISO 14122-1
2001-05
Safety of machinery. Permanent means of access to machines and industrial plants. Part 1: Choice of a fixed means of access between two levels
X
150 ISO 14122-2
2001-05
Safety of machinery. Permanent means of access to machines and industrial plants. Part 2: Working platforms and Walkways
X
151 ISO 14122-3
2001-05
Safety of machinery. Permanent means of access to machines and industrial plants. Part 3: Stairways, stepladders and guardrails
X
152 ISO 14122-4
2004-12
Safety of machinery. Permanent means of access to machines and industrial plants. Part 4: Fixed ladders
X
153 ISO 2553
1992-10
Welded, brazed and soldered joints. Symbolic representation on drawings
X
154 EN 22553
1994-05
Welded, brazed and soldered joints. Symbolic representation on drawings (ISO 2553:1992)
X
155 ISO 4354
1997-07
Wind actions on structures (Relationship between reference velocity pressure… )
X
156 SFS-ENV 1993-1-1
1993-11
Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings
157 SFS-ENV 1993-11/A1 D
1996-03
Eurocode 3: Design of steel structures. Part 1-1: General. General rules and rules for buildings
X
Korvataan standardeilla SFS-EN 1993-1-1:2005, SFS-EN 1993-18:2005, SFS-EN 1993-1-9:2005 ja SFS-EN 1993-1-10:2005 viimeistään 2010-03-31
X
Korvataan standardilla SFS-EN 1993-1-1:2005 viimeistään 2010-0331
STANDARDILUETTELO
14(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
158 SFS-ENV 1993-11/A2 G
Vahvistus- Otsikko pvm Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for 1999-11 buildings. Annex G: Design for torsion resistance
X
159 SFS-ENV 1993-11/A2 H
1999-11
160 SFS-ENV 1993-11/A2 J
1999-11
Eurocode 3: Design of steel structures. Part 1-1: General. General rules and rules for buildings
X
161 SFS-ENV 1993-11/A2 N
1999-11
Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings. Annex N: Opening in webs
X
162 SFS-ENV 1993-11/A2 Z
2000-01
163 SFS-ENV 1993-1-2
1996-09
164
SFS-ENV 1993-1-4
1999-02
Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings. Annex H: Modelling of building structures for analysis
Voimassa
Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings. Annex Z: Determination of design resistance from tests Eurocode 3. Design of steel structures. Part 1-2: General rules. Structural fire design
Eurocode 3: Design of steel structures. Part 1-4: General rules. Supplementary rules for stainless steels
X
X
X
---”-----”-----”-----”-----”--Korvataan standardilla SFS-EN 1993-1-2:2005 viimeistään 2010-0331
X
Eurocode 3: Design of steel structures. Part 1-5: General rules. Supplementary rules for planar plated structures without transverse loading Eurocode 3: Design of steel structures. Part 3-1: Towers, masts and chimneys. Towers and masts
X
Eurocode 1: Basis of design and actions on structures. Part 1: Basis of design
X
165 SFS-ENV 1993-1-5
1999-02
166 SFS-ENV 1993-3-1
1999-02
167 SFS-ENV 1991-1
1995-10
168 SFS-EN 1991-1-1
2002-10
169 SFS-EN 1991-1-2
2003-04
170 SFS-EN 1991-1-3
2004-01
Eurocode 1: Actions on structures. Part 1-3: General actions. Snow loads
X
171 SFS-EN 1991-1-4
2005-09
Eurocode 1: Actions on structures. Part 1-4: General actions. Wind actions
X
172 SFS-EN 1991-1-5
2004-05
Eurocode 1: Actions on structures. Part 1-5: General actions. Thermal actions
X
173 SFS-EN 1991-1-6
2005-08
Eurocode 1. Actions on structures Part 1-6: General actions. Actions during execution
X
Eurocode 1: Actions on structures. Part 1-1: General actions. Densities, selfweight, imposed loads for buildings Eurocode 1. Actions on structures. Part 1-2: General actions. Actions on structures exposed to fire
Uusi/korvaava standardi
X
X X
Korvataan standardilla SFS-EN 1990:2002 viimeistään 2010-03-31
STANDARDILUETTELO
15(15)
Tarkistuspäivämäärä
12.10.2006 Kpl
Standardin numero
Vahvistus- Otsikko pvm
Voimassa
Uusi/korvaava standardi